Domenor D8406 Installation And Operation Manual Download Page 39

Page: 39 / 43

No action, no
video after
power up

Possible causes

Trouble

Solution

10. 2 Trouble shooting

Power line is bad connection

Correct

Engineering line is malfunction

Self-testing and

image are normal

but the dome is

uncontrollable

The dome DIP switch setting is incorrect

Refer to switch setting, reset the switch

Rs485 may carve out a way

Check Rs485connection, confirm
the connection is correct and
good in contact

Rs485 is in malfunction

Pls consult appendix

Rs485

Bus acknowledge

“

”

Video image

is not steady.

Video line is bad connection

Eliminate

Power consumption is not enough

Video image is not

steady and the

motor is malfunction

Power consumption is not enough

Replace the power

Dome controlling

is not smooth.

Controlling line is bad connection

Rs485 loads so many or the distance

of communication is much far

1.Connect 120

resistance in the dome pan/tilt

that is far from the controller

2.Increase distributor

Power supply is damage or
power consumption is not enough

Replace

Replace right power adapter, it is better to put
the switch and power adapter near the dome

To obtain constant clear videos, user should

clean the down cover periodically.

Be caution when cleaning, hold the down cover

ring only to avoid direct touch to the acrylic down

cover. The acid sweat mark of fingerprint will corrode

the coating of down cover and scratch on down cover

will cause vague image.

Use soft dry cloth or the substitute to clean the inner and outer surfaces

For hand contamination, use neutral detergent. Any cleanser for high grade furniture

is applicable.

●

10. 3 The cleaning of clear down cover

Check and repair

Appendix

Summary of Contents for D8406












































Search results

Summary of Contents for D8406

Reviews:

Related manuals for D8406

Brands by name

Popular brands

Domenor D8406, Installation And Operation Manual

Search results

Summary of Contents for D8406

Reviews:

Related manuals for D8406

Brands by name

Popular brands