Dodge HORNET 2023 Owner'S Manual Download Page 96

Page: 96 / 288

STARTING AND OPERATING

Adaptive Cruise Control Off
When ACC is deactivated, all ACC visualizations will not be

shown in the instrument cluster display.
Adaptive Cruise Control Ready
When ACC is activated, but the vehicle speed setting has

not been selected, the white ACC icon will illuminate above

dashes in place of a speed in the instrument cluster

display.
Adaptive Cruise Control Set
When the vehicle has reached the desired speed, push

the SET switch up or down briefly, then release. When the

ACC speed is set, the green ACC icon over the set speed

will illuminate in the instrument cluster display.
When the ACC menu screen is not being viewed in the

instrument cluster display, a green triangle will illuminate

on the speedometer at the location of the set speed.

NOTE:

If the ACC system is canceled or paused, the triangle on

the speedometer will change to white, indicating the

saved set speed for when the RES button pushed.

Activating Adaptive Cruise Control (ACC)

The minimum set speed for the ACC system is 19 mph

(30 km/h).

NOTE:

You cannot engage ACC under the following conditions:



When the brakes are applied



When the parking brake is applied



When the gear selector is in PARK, REVERSE or

NEUTRAL



When the vehicle speed is below the minimum speed

range



When the brakes are overheated



When the driver’s door is open at low speeds



When the driver’s seat belt is unbuckled at low speeds



When there is a stationary vehicle in front of your

vehicle in close proximity

To Activate/Deactivate

Push and release the Mode button located on the left side

of the steering wheel to activate ACC. Then proceed to

setting the desired speed as described in the next section.

NOTE:

Active Speed Limiter will be unavailable while ACC is in

use.
To turn the system off, push and release the Mode button

again. At this time, the system will turn off and Active

Speed Limiter will be active.
The system will also turn off during any of the conditions

listed in “To Turn Off”

page 95.

To Set A Desired Speed

When the vehicle has reached the desired speed, push

the SET switch up or down briefly, then release. The

instrument cluster display will show the set speed.

If ACC is set when the vehicle speed is below 19 mph

(30 km/h), the set speed will default to 19 mph (30 km/h).
If either system is set when the vehicle speed is above

19 mph (30 km/h), the set speed shall be the current

speed of the vehicle.

NOTE:



Keeping your foot on the accelerator pedal can cause

the vehicle to continue to accelerate beyond the set

speed.



If you continue to accelerate beyond the set speed

while ACC is enabled, the system will not be controlling

the distance between your vehicle and the vehicle

ahead. The vehicle speed will only be determined by

the position of the accelerator pedal.

WARNING!

Leaving the Adaptive Cruise Control (ACC) system on

when not in use is dangerous. You could accidentally

set the system or cause it to go faster than you want.

You could lose control and have a collision. Always leave

the system off when you are not using it.

WARNING!

If the Active Speed Limiter is active, the system will not

react to vehicles ahead. In addition, the proximity

warning does not activate and no alarm will sound even

if you are too close to the vehicle ahead since neither

the presence of the vehicle ahead nor the

vehicle-to-vehicle distance is detected. Be sure to

maintain a safe distance between your vehicle and the

vehicle ahead. Always be aware which mode is

selected.

23_GG_OM_EN_USC_t.book Page 94

Summary of Contents for HORNET 2023

































































































































































































































































































Search results

Summary of Contents for HORNET 2023

Reviews:

Brands by name

Popular brands

Dodge HORNET 2023, Owner'S Manual

Search results

Summary of Contents for HORNET 2023

Reviews:

Brands by name

Popular brands