Dodge HORNET 2023 Owner'S Manual Download Page 126

Page: 126 / 288

124

STARTING AND OPERATING

Towing Requirements — Tires



Do not attempt to tow a trailer while using a compact

spare tire.



Do not drive more than 50 mph (80 km/h) when towing

while using a full size spare tire.



Proper tire inflation pressures are essential to the safe

and satisfactory operation of your vehicle.



Check the trailer tires for proper tire inflation pressures

before trailer usage.



Check for signs of tire wear or visible tire damage

before towing a trailer.



Replacing tires with a higher load carrying capacity will

not increase the vehicle's GVWR and GAWR limits.



For further information

page 246.

Towing Requirements — Trailer Brakes



Do not interconnect the hydraulic brake system or

vacuum system of your vehicle with that of the trailer.

This could cause inadequate braking and possible

personal injury.



An electronically actuated trailer brake controller is

required when towing a trailer with electronically

actuated brakes. When towing a trailer equipped with

a hydraulic surge actuated brake system, an electronic

brake controller is not required.



Trailer brakes are recommended for trailers over

1,000 lb (453 kg) and required for trailers in excess of

1,543 lb (700 kg).

Towing Requirements — Trailer Lights And

Wiring

Whenever you pull a trailer, regardless of the trailer size,

stoplights and turn signals on the trailer are required for

motoring safety.
The Trailer Tow Package may include a four- and seven-pin

wiring harness. Use a factory-approved trailer harness and

connector.

NOTE:

Do not cut or splice wiring into the vehicle’s wiring

harness.
The electrical connections are all complete to the vehicle

but you must mate the harness to a trailer connector.

Refer to the following illustrations.

NOTE:



Disconnect the trailer wiring connector from the vehicle

(or any other device plugged into vehicle’s electrical

connectors) before launching a boat into water.



Be sure to reconnect once clear from water area.

WARNING!



Do not connect trailer brakes to your vehicle's

hydraulic brake lines. It can overload your brake

system and cause it to fail. You might not have

brakes when you need them and could have an

accident.



Towing any trailer will increase your stopping

distance. When towing, you should allow for

additional space between your vehicle and the

vehicle in front of you. Failure to do so could result

in an accident.

CAUTION!

If the trailer weighs more than 1,000 lb (453 kg)

loaded, it should have its own brakes and they should

be of adequate capacity. Failure to do this could lead to

accelerated brake lining wear, higher brake pedal

effort, and longer stopping distances.

23_GG_OM_EN_USC_t.book Page 124

Summary of Contents for HORNET 2023

































































































































































































































































































Search results

Summary of Contents for HORNET 2023

Reviews:

Brands by name

Popular brands

Dodge HORNET 2023, Owner'S Manual

Search results

Summary of Contents for HORNET 2023

Reviews:

Brands by name

Popular brands