manualshive.com logo in svg

Dodge HORNET 2023, Owner'S Manual

Share
Download
Dodge HORNET 2023 Owner'S Manual Download Page 32

30

GETTING TO KNOW YOUR VEHICLE

 

Reclining The Seatback Forward Or 

Rearward

The seatback can be reclined both forward and rearward. 

Push the seat recliner switch forward or rearward. The 

seatback will move in the direction of the switch. Release 

the switch when the desired position has been reached.

Power Lumbar — If Equipped

Vehicles equipped with power driver or passenger seats 

may be equipped with power lumbar. The power lumbar 

switch is located on the outboard side of the power seat. 

Push the switch forward to increase the lumbar support. 

Push the switch rearward to decrease the lumbar support. 

Pushing upward or downward on the switch will raise and 

lower the position of the support.

Power Lumbar Switch

F

RONT

 H

EATED

 S

EATS

 — I

F

 E

QUIPPED

The front heated seats control buttons are 

located within the Uconnect system. You can 

gain access to the control buttons through the 

climate or controls screen.

Press the heated seat button once to turn the 

HI setting on.

Press the heated seat button a second time to turn the 

MED setting on.

Press the heated seat button a third time to turn the

LO setting on.

Press the heated seat button a fourth time to turn the 

heating elements off.

If the HI level setting is selected, the system will 

automatically switch to a lower level after approximately 

15 minutes (depending on environmental conditions) of 

continuous operation. The heated seat feature will then 

turn off automatically approximately 45 minutes after 

switching to a lower level.

NOTE:

The engine must be running for the heated seats to 

operate.
For information on use with the Remote Start system, see  

Ú

page 19.

WARNING!

Do not ride with the seatback reclined so that the 

shoulder belt is no longer resting against your chest. 

In a collision you could slide under the seat belt, which 

could result in serious injury or death.

WARNING!

Persons who are unable to feel pain to the skin 

because of advanced age, chronic illness, diabetes, 

spinal cord injury, medication, alcohol use, exhaus

-

tion or other physical condition must exercise care 

when using the seat heater. It may cause burns even 

at low temperatures, especially if used for long 

periods of time.

Do not place anything on the seat or seatback that 

insulates against heat, such as a blanket or cushion. 

This may cause the seat heater to overheat. Sitting in 

a seat that has been overheated could cause serious 

burns due to the increased surface temperature of 

the seat.

23_GG_OM_EN_USC_t.book  Page 30  

Summary of Contents for HORNET 2023

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands