manualshive.com logo in svg

Dodge HORNET 2023, Owner'S Manual

Share
Download
Dodge HORNET 2023 Owner'S Manual Download Page 214

212

IN CASE OF EMERGENCY

 

(Continued)

I

NFLATION

 P

ROCEDURE

NOTE:

Always follow applicable state and provincial laws. Contact 

state and provincial Highway Safety offices for additional 

details.
To use your Tire Inflator Kit, proceed as follows:
1. Stop the vehicle in a position where you can repair 

the tire safely. Activate the Hazard Warning Flashers 

to make other drivers aware of your presence.

2. If equipped, use all available safety equipment 

required by law.

3. Verify that the valve stem (on the wheel with the 

deflated tire) is in a position that is near to the 

ground. This will allow the Tire Inflator Kit hoses to 

reach the valve stem and keep the tire repair kit flat 

on the ground.

4. Place the gear selector to PARK (P).
5. Apply the Electric Park Brake and cycle the 

engine OFF.

6. Insert the sealant cartridge containing the sealing 

fluid in the proper compressor holder, pushing down 

hard. Unscrew the tire valve cap, take out the filler 

tube and tighten the fitting on the tire valve.

WARNING!

The information required by current legislation is 

shown on the kit cartridge label. Read the cartridge 

label before use, avoid improper use.

Do not attempt to seal a tire on the side of the

vehicle closest to traffic. Pull far enough off the 

road to avoid the danger of being hit when using

the Tire Service Kit.

Do not remove foreign bodies from the tire.

Do not leave the compressor running for more than 

20 minutes, this may cause overheating.

Do not use the Tire Service Kit or drive the vehicle 

under the following circumstances:

If the puncture in the tire tread is approximately 

1/4 inch (6 mm) or larger.

If the tire has any sidewall damage.

If the tire has any damage from driving with 

extremely low tire pressure.

If the tire has any damage from driving on a 

flat tire.

If the wheel has any damage.

If you are unsure of the condition of the tire or 

the wheel.

Keep the Tire Service Kit away from open flames or 

heat sources.

A loose Tire Service Kit thrown forward in a collision 

or hard stop could endanger the occupants of the 

vehicle. Always stow the Tire Service Kit in the place 

provided. Failure to follow these warnings can result 

in injuries that are serious or fatal to you, your 

passengers, and others around you.

Take care not to allow the contents of the Tire 

Service Kit to come in contact with hair, eyes, or 

clothing. Tire Service Kit sealant is harmful if inhaled, 

swallowed, or absorbed through the skin. It causes 

skin, eye, and respiratory irritation. Flush immedi

-

ately with plenty of water if there is any contact with 

eyes or skin. Change clothing as soon as possible, if 

there is any contact with clothing.

Tire Service Kit sealant solution contains latex. In 

case of an allergic reaction or rash, consult a physi

-

cian immediately. Keep the Tire Service Kit out of 

reach of children. If swallowed, rinse mouth immedi

-

ately with plenty of water and drink plenty of water. 

Do not induce vomiting! Consult a physician immedi

-

ately.

WARNING!

23_GG_OM_EN_USC_t.book  Page 212  

Summary of Contents for HORNET 2023

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands