Docomo P-02A, Instruction Manual

Page: 124 / 212

122
S
e
cu
rity S
e
ttin
g
s
For some functions of the FOMA terminal, you need to enter your
security code. In addition to the Terminal Security Code for operating
respective mobile phone functions, the Network Security Code to use
network services, and i-mode password are available. These security
codes help you utilize your FOMA terminal.
The Terminal Security Code is set to “0000” at purchase but you can
change it by yourself. (See page 12
3 )
When the display for entering the Terminal Security Code appears, enter
your four- to eight-digit code and press
O o
( ).
≥
When you enter your Terminal Security Code, the entered
numbers are indicated by “_” and not displayed.
≥
If you have entered wrong numbers or nothing for about 15
seconds, a warning tone sounds and a warning message is
displayed; then the display prior to entering the Terminal
Security Code returns. Check the correct code and retry entering numbers.
Security Codes Used for FOMA Terminal
■
Cautions on security codes
≥
You should avoid using the numbers for security codes such as denoting your birth
date, part of your phone number, local address number, room number, “1111” or
“1234” that is easily decoded by a third party. Also make sure that you take a note of
the security codes you have selected just in case you forget them.
≥
Take care not to let others know your security codes. Even if your security codes are
known and used by a third party, we at DOCOMO take no responsibility in any event
for the resultant loss.
≥
If you do not remember your respective security codes, you need to bring an
identification card such as your driver’s license, the FOMA terminal and UIM to the
handling counter of a docomo shop.
For details contact “docomo Information Center” on the back page of this manual.
Terminal Security Code
This is a four-digit number required for your identification to give orders
at a docomo shop, docomo Information Center, or “
各種お申込・お手続
き
(Respective applications/ procedures)” site, or when you use
respective network services. This is determined at the time of contract
but can be changed by yourself.
If you have “docomo ID/Password” for “My docomo”, the overall support
site for personal computers, you can use a personal computer to take
proceedings of changing your Network Security Code to new one.
Further, you can change it by yourself from “
各種お申込・お手続き
(Respective applications/procedures)” of “
お客様サポート
(User
support)” from i-mode.
※
For “My docomo” and “
各種お申込・お手続き
(Respective applications/
procedures)”, see the inside of the back page of this manual.
You need to enter the four-digit “i-mode password” for registering or
deleting My Menu, applying for or canceling Message Services, i-mode
pay service, and so on. (Some information providers may provide you
with their specific password.)
The i-mode password is “0000” at the time of your contract, but you can
change it by yourself. (See page 195)
From i-mode, you can change the i-mode password by following
operation:
“
i
Menu” → “English” → “Options” → “Change i-mode Password”
For the UIM, you can set two security codes, namely the PIN1 code and
PIN2 code. These security codes are “0000” at the time of your contract,
but you can change them by yourself. (See page 124)
The PIN1 code is a four- to eight-digit number for checking the user each
time the UIM is inserted into the FOMA terminal or each time the FOMA
terminal is turned on, so that you can prevent the third party from using
your UIM. By entering your PIN1 code, you can make or answer calls, or
use functions in the FOMA terminal.
The PIN2 code is a four- to eight-digit number for executing Reset Total
Cost, using the user certificate or applying for the issue of it, etc.
Network Security Code
i-mode Password
PIN1 Code/PIN2 Code