DITEC GLOBE IP1839, Installation And Maintenance Manual

Page: 19 / 64

GB
19 GLOBE - IP1839
1. TECHNICAL DETAILS
GLOBE7 GLOBE7J GLOBE10
GLOBE10J
Power supply
230 V~ / 50-60 Hz 120 V~ / 50-60Hz 230 V~ / 50-60 Hz
120 V~ / 50-60Hz
Absorption
0,7 A 1,4 A 1,2 A
2,4 A
Fuse F1
F1,6A F3,15A F1,6A
F3,15A
Thrust 500 N 500 N 900 N
900 N
Max stroke
2500 mm 2500 mm 2500 mm
2500 mm
Max load 7 m² 7 m² 10 m²
10 m²
Opening speed 0,15 m/s (chain)
0,18 m/s (belt)
0,15 m/s (chain)
0,18 m/s (belt)
0,15 m/s (chain)
0,18 m/s (belt)
0,15 m/s (chain)
0,18 m/s (belt)
Closing speed 0,10 m/s (chain)
0,12 m/s (belt)
0,10 m/s (chain)
0,12 m/s (belt)
0,10 m/s (chain)
0,12 m/s (belt)
0,10 m/s (chain)
0,12 m/s (belt)
Service class 3 - FREQUENT 3 - FREQUENT 3 - FREQUENT
3 - FREQUENT
Intermittence S2 = 30 min
S3= 50%
S2 = 30 min
S3= 50%
S2 = 30 min
S3= 50%
S2 = 30 min
S3= 50%
Temperature -20° C / +55° C -20° C / +55° C -20° C / +55° C
-20°C / +55°C
Degree of protection IP10 IP10 IP10
IP10
Control panel 70R 70R 71R
71R
2. REFERENCE TO ILLUSTRATIONS
The given operating and performance features can only be
guaranteed with the use of DITEC accessories and safety
devices.
2.1 Standard installation references (fig. 1)
[1] Radio
[2] Drive unit
[3] Retention bracket
[4] Slide
[5] Release cord
[6] Guide
[7] Guide coupling
[8] Transmission
[9] Photocells
[10] Sensitive edge
[11] Connect the power supply to an omnipolar switch with
contact opening distance of at least 3 mm (not supplied)
or by means of power plug.
Connection to supply mains must be carried out in an
independent raceway separate from control connections
and safety device connections.
2.2 Accessories
BATK1 Battery kit
GLOBEC Adapter for up and over doors with counterweights
ASB1 External release kit with cord and lock
ASB2 Cord release device
GLOBEL Extension set for chain
GLOBELV Extension set for belt (for steel guide only)
GLOBEFM Additional close stop
GLOBESI Intermediate support
GLOBEGF Iron track
GLOBEGA Aluminium track
3. INSTALLATION
3.1 Chain type GLOBE assembly (fig. 4)
- Extend the chain.
- Fit the coupling [1] as far as the guide stop. Fit the guide
[2] as far as the stop. Fit the coupling [3] as far as the guide
stop [2].
- Superimpose the guide [4] on the coupling [3], correctly fit
the transmission in the guide [4]: lift the guide as shown in
the detail to permit fitting the transmission.
- Move the coupling [3] towards the transmission as far as
the guide stop [4].
Note: the guides must be fitted in a specific direction (see stops
[x] shown in figure).
3.2 Belt type GLOBE assembly (fig.5)
- (fig. 5a) Fit the belt to the transmission and slide.
- (fig. 5b) Fit the belt stop as shown in the illustration.
- (fig. 5c) Fasten the two ends of the belt to the release pin
by means of the couplings keeping to the pin direction
shown in the illustration.
- (fig. 5d) Fit the drive pin (belt - transmission - slide) in the
guide.
- (fig. 5e) Pass the belt around the pulley and secure by
means of the pin [Y]. Fit the guide as shown in fig. 3, lock
in the drive unit as far as the stop and tighten screw [K].
- (fig. 5f) Push the transmission towards the outside of the
guide and fasten the retention bracket to the wall.
3.3 Chain or belt tensioning (fig.6)
- Correct tensioning is achieved by leaving 1÷2 mm between
the spring retainer [E] and stop [H] to enable the spring [E]
to work in the best possible way.
Attention: over-tightening could affect proper operation of the
automatic system.
E H
1÷2