background image

Useful tip: to ensure long-term operation of the generator 

engine, it is important to observe the following tips:

- Before connecting the load, allow the engine to run for 1-2 minutes to warm it up.
-  When disconnecting the load after lengthy operation, do not turn off the generator. Allow 

the generator to run idle for 1-2 minutes so that it cools down.

IMPORTANT!

5. Pull the manual starter until a slight resistance is felt, then pull 

it toward you relatively sharply. Slowly turn the manual starter by 

hand, do not release it abruptly.
6. Turn the air choke control knob to the “RUN” position.

Fig.  3

Do not connect two or more devices at a time. The start-

up of many devices requires high power. Devices should be 

connected one at a time according to their power rating. 

Do not connect any power consumers within the first 

2 minutes after the generator has been started.

ATTENTION – DANGER!

“ON” MODE
When the ECON switch is in the “ON” position, the control unit monitors the engine speed, reducing it 

commensurate with the connected load. If the engine speed is not enough to generate electricity to provide 

the load, the control unit will automatically increase the engine speed. 
As a result, fuel consumption is optimized and noise levels are reduced.

The ECON switch must be set to “OFF” to increase 

engine speed to nominal. When connecting multiple 

power consumers to the generator, be sure to first 

connect the one with the highest starting current, and 

the device with the lowest starting current should be 

connected last.

IMPORTANT!

ECON FUNCTION

1. Start the engine.

2. Set the ECON switch to “ON”.

3. Plug the device into an AC outlet.

4. Make sure the AC indicator light is on.

5. Turn on the electrical device.

FUNCTIONAL DESCRIPTION 

OF INVERTER GENERATORS

8

“OFF” MODE
The ECON switch must be set back to “OFF” when using electrical devices requiring a high starting current, 

such as a compressor or submersible pump.

The ECON switch must be set back to “OFF” when using 

electrical devices requiring a high starting current, such 

as a compressor or submersible pump.

IMPORTANT!

www.ks-power.de/en

   

|

    24

Summary of Contents for Konner & Sohnen 4260405363322


















Reviews: