DIGITIZE DGM-32/64 Installation And Maintenance Manual Download Page 15 | Manualshive

Page: 15 / 59

background image

DGM INSTALLATION AND MAINTENANCE MANUAL

700135-0000 Rev. O

5

NOTE: Weights specified are for typical units. Actual weights may vary based on the options
installed on the DGM. Shipping weights may vary based on packaging methods.

1.4.7 TEMPERATURE AND HUMIDITY

Operating Temperature Range - 40 to + 60 Degrees Celsius

Storage Temperature Range

- 40 to + 60 Degrees Celsius

Operating Humidity Range

0 to 90 % (non-condensing)

Storage Humidity Range

0 to 90 % (non-condensing)

1.5 F.C.C. REQUIREMENTS

The DGM complies with the limits set for a Class B computing device as specified in
Subpart J of Part 15 of The FCC Rules and Regulations.

1.6 APPLICABLE PUBLICATIONS

-

Federal Communications Commission “Rules and Regulations” - National Electric

Code (1990)

- National Fire Protection Association (NFPA) 72 (1990)

«
...
13
14
15
16
17
...
»

Summary of Contents for DGM-32/64




























































Reviews:

No comments

Related manuals for DGM-32/64

Brand: Samsung Wisenet Pages: 16

Brand: Panasonic Pages: 27

Brand: Mackie Pages: 17

Brand: NEO TOOLS Pages: 17

Brand: Vicon Pages: 28

Brand: Cambridge SoundWorks Pages: 11

thombox Security pack

Brand: THOMSON Pages: 8

Brand: GCE Pages: 28

RainStation RS-0001

Brand: EarthMinded Pages: 16

Brand: i3 International Pages: 28

MicroView MVIC-04IR-E

Brand: ERNITEC Pages: 31

Brand: Parweld Pages: 16

Brand: Parweld Pages: 16

Brand: Black Pages: 27

Brand: chinavasion Pages: 2

Brand: Dahua Pages: 25

Brand: Hoshizaki Pages: 10

Brand: SICK Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands