manualshive.com logo in svg

Digital Audio Corporation PCAP II, User Manual

Share
Download
Digital Audio Corporation PCAP II User Manual Download Page 76

64 

 

4.4.6  Bandstop Filter 

 
Application: 
 

 

The Bandstop filter is used to decrease the energy level 
(lower the volume) of all signal frequencies above a specified 
Lower Cutoff Frequency and below a specified Upper Cutoff 
Frequency.  The signal region between the Lower Cutoff 
Frequency and the Upper Cutoff Frequency is called the 
stopband region.  The Bandstop filter is useful for removing 
in-band noise from the input signal. 

 
 

The Lower Cutoff Frequency is usually set below the 
frequency range of the noise, while the Upper Cutoff 
Frequency is set above the frequency range of the noise.  
While listening to the filter output audio, the Lower and Upper 
Cutoff Frequencies can be incrementally adjusted to achieve 
maximum elimination of noise while minimizing loss of voice. 

 

 

The amount of volume reduction in the stopband region can 
further be controlled by adjusting the Stopband Attenuation 
setting (maximum volume reduction is 60dB).  The slope at 
which the volume is reduced from normal (at each Cutoff 
Frequency) to the minimum volume (specified by Stopband 
Attenuation) can also be controlled by adjusting the 
Transition Slope setting. 

 
Description of controls is as follows: 
 
Lower Cutoff  

 

Specifies frequency in Hertz below which no 

Frequency: 

 

signals are attenuated.  Frequencies 
between this cutoff and the Upper Cutoff 
Frequency are attenuated.  Minimum Lower 
Cutoff Frequency is 0 Hz, while the 
maximum Lower Cutoff Frequency is 10 Hz 
below the Upper Cutoff Frequency.  Lower 
Cutoff Frequency can be adjusted in 1 Hz 
steps. 

 
 

 

 

NOTE:

  The Lower Cutoff Frequency can 

never be set higher than 10 Hz below the 
Upper Cutoff Frequency. 

Summary of Contents for PCAP II





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands