www.digimerge.com
VCE400 Series QSG_EN_R1 Page 5
Information in this document is subject to change without notice. As our products are subject to continuous improvement, Digimerge Technologies Inc. reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE © 2007 Digimerge. All rights reserved.
5
b
STEP 2
SETTING UP YOUR DIGTIAL VIDEO RECORDER (DVR)
- MOTION DETECTION, RECORD PROGRAM SETUP
Press the
“Menu”
Button
Use the Left or Right Arrows to Navigate to the
“Event”
Menu
Select
“Motion Detection”
and press
“status/home/enter”
In this menu, you can modify the Sensitivity for each cam-
era, along with the motion detection area; “dead zones” can be
configured in areas where there will be constant or unwanted
motion
Channel:
This will display which channel number you are modi-
fying, Use the
“F-” (auto) or “F+” (freeze)
keys to decrement
or increment the Channel value
Sensitivity: This will show the current sensitivity for the for
the selected channel;
“1”
is the lowest,
“5”
is the highest; by
default this value is
“3”,
Use the
“F-”
(auto) or
“F+”
(freeze)
keys to decrement or increment the sensitivity value
Area Setup:
This menu will allow you to configure your ‘dead
zones’ or areas in which you do not want the VCE400 to de-
tect motion; Press the
“status/home/enter”
, and use the
arrow keys to highlight which square you wish to block
out. Press the
“status/home/enter”
key. This will remove the
green tint from the selected square. The VCE400 will ignore
motion in all of the non-green squares. By default, all
the detection areas are turned “On” (green).
Press
“Spot/ESC”
to set the motion area
Press
“Spot/ESC”
2 more times
Move to
“Save and Exit”
and press
“status/home/enter”
Motion Detection
Area Setup
6
Record Program
Setup
Use the
“F-” (auto) or “F+” (freeze)
keys to decrement or in
crement the Resolution value; the options are (320x240,
720x240, 720x480)
Setting Normal (continuous) Record IPS
The Normal IPS Settings are only used when the “Record”
button is pressed.
Please refer to Chart#1 for Maximum record IPS (images per
second) per channel for each resolution
The maximum IPS value per channel is 30 ips
Move down to highlight the values located below the
“Normal
IPS”
Column
Use the
“F-” (auto) or “F+” (freeze)
keys to decrement or incre-
ment the highlighted Normal IPS values
Repeat this process for each Channel
The Sum of these IPS values cannot exceed the Maximum IPS
for the desired resolution
Note: if you are planning on connecting to the DVR over the
network, do not set the “Normal IPS” to a value lower then 1
IPS per channel, as the “live” video will not be transmitted over
the network
CHANNEL
SENSITIVITY
AREA SETUP
TEST MOTION
Chart #1
Recording Program Setup (Custom Program Setup)
Press the
“Menu”
Button
Use the Left or Right Arrows to Navigate to the
“Record”
Menu
Move down to
“Record Program”
and press
“status/home/enter”
The Record Program menu defines how you want the DVR to
record, this includes Resolution, Normal IPS, Event
IPS, Quality, Pre-Alarm, and Post Alarm Settings.
Use the arrow keys to highlight which entry to modify
At the top of the screen, make sure that
“Rec Program”
is set to
“Program0”
Use the
“F-” (auto) or “F+” (freeze)
keys to switch
Program Numbers
At the top of the screen, make sure that
“Event Rec Type”
is
set to
“Complex/Event CH Only”
, Use the
“F-” (auto) or “F+”
(freeze)
keys to switch Record Program Type
Setting the Recording Resolution
Please refer to Chart#1 for Maximum record IPS (images per
second) per channel for each resolution
Move down to highlight the value located below the
“Image
Size”
Column
VCE400 Resolution
VCE416
Total IPS
VCE416 Max
IPS / Channel
VCE408
Total IPS
VCE408 Max
IPS / Channel
VCE404
Total IPS
VCE404 Max
IPS / Channel
360x240
480
30
240
30
120
30
720x240
240
15
120
15
120
30
720x480
120
7.5
60
7.5
120
30
