Digimerge VCD304161 Installation And User Manual Download Page 83

Page: 83 / 91

7.2

Specifications.

VCD304

VCD308

VCD316

CPU

X86 CPU

RAM

128MB

H/W

HDD

Max. 3HDD (2HDD + CD-RW)

Embedded Linux

Video Input

4ch 8ch 16ch

Loop-OUT

4ch None None

Video Mode

NTSC / PAL Selectable

Display Speed (NTSC/ PAL)

120/100fps

Screen Modes for Live Display

4/1/PIP 8/4/1/PIP

16/10/9/4/1/PIP

352x240 /288

120/100fps (with Playback : 60/50fps)

704x240/288

60/50fps (with Playback : 30/25fps)

Recording speed

(NTSC/ PAL)

704x480/288

30/25fps (with Playback : 15/12.5fps)

Monitor output

Main monitor output (Composite & S-Video, VGA) / Spot output (Composite)

Recording Resolution

NTSC: 352x240, 704x240, 704x480

PAL : 352x288, 704x288, 704x576

Byte Size per Image
(Standard Quality)

3~5Kbyte @352x240 (PAL: 352x288)

5~10Kbyte @704x240 (PAL: 704x288)

10~20Kbyte @704x480 (PAL: 704x576)

Recording Modes

Supports the Setting of Motion Sensitivity & Area per Camera

Recording schedule

Setting Recording Schedule per camera

Motion Detection

Support the Setting of Motion Sensitivity per Camera

Sensor/ Camera/ Alarm I/O

M : N Mapping

Audio Input/ Output

4 input / 1 output (ADPCM)

Sensor/ Alarm

4 Dry Contact Input / 2 Relay Output

P/T/Z control and port

PAN/TILT/ZOOM/FOCUS/IRIS, RS-485 port

LAN

10/100 Ethernet

Transmission Speed
and No. of Connection

Same as Recording Speed for each Channel

Max 8 ch Connection

Remote Transmission

Multi-to-Multi connection, Multi-channel transmission

Live Viewing, Remote Playback and File Backup at the same time (Triplex-on-Remote)

Remote Control

Remote PAN Tilt ZOOM/FOCUS /IRIS control

Remote management

Remote Software Upgrade & Remote Software Upgrade

CD-RW

Internal CD-RW (Option)

External Backup Device

Support (Front USB Ports)

System Recovery after Power Failure

Auto-Rebooting and Journaling File System

Auto-Scan and Recovery for Data

System Operation

Button on Front panel / IR Remote Controller / Jog / Shuttle

Advanced Functions

Auto Page Sequencing, Event Log Viewer, Access control by Password

Led indicator for Various status

Pre-Alarm, Multi Channel Playback, Digital Zoom

Storage Temperature and Humidity

-20~60 / 20~95%RH

Operating Temperature and Humidity

5~40 / 20~80%RH

Power

Single Phase AC115~230V, 50/60Hz (Select Switch)

Dimension and Weight

380(W) x 66(H) x 370(D) mm, 6Kg

Remote S/W

NetAgent S/W (24ch), RemoteAgent S/W (16ch)

Standard Authentication

FCC,

, CE (EMC/LVD) – CLASS A

* The system specification can be modified without notification.

Because our products are subject to continuous improvement, Digimerge and its subsidiaries reserve the right to modify

product design and specifications without notice and without incurring any obligation. E&OE

Summary of Contents for VCD304161




























































































Search results

Summary of Contents for VCD304161

Reviews:

Brands by name

Popular brands

Digimerge VCD304161, Installation And User Manual

Search results

Summary of Contents for VCD304161

Reviews:

Brands by name

Popular brands