manualshive.com logo in svg

Digimerge VCD304161, Installation And User Manual

Share
Download
Digimerge VCD304161 Installation And User Manual Download Page 18

 

9

 

 

 
 
 
 
 
VCD316.                  Upper port of I/O 
                                  Terminal Block 
 
 
 
 
                       
 

 
 

2.4.1. VGA 

Port 

Use to connect a normal PC Monitor for local setup/surveillance. 
 

2.4.2. LAN 

Port 

Connect the RJ-45 jack of the LAN cable to the LAN port. The Network has to be TCP/IP base 10/100 Ethernet LAN (Local 
Area Network), Internet or exclusive line, and the IP address should be fixed. Consult your network administrator for proper 
network configuration. 
 

2.4.3. Power 

Input 

Connect to main power cord of the system.   
 

Caution 

Before plugging-in the power cord to the system, check if the power is in accordance with the system 
specification (Single Phase AC 115~230V)

 

 

2.4.4.  Input Power Switch 

Input power can be used in accordance with the user environment. Check input power before inputting power.   
 

2.4.5.

 

USB Port   

Connect a USB storage device for image archiving or Firmware updating. 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

      TX+      TX- 

      RS485A    RS485B 

Summary of Contents for VCD304161




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands