DENT Instruments powerscout 3037 Operator'S Manual Download Page 25

Page: 25 / 107

Communications LEDs

The PowerScout COM LEDs signal the following communication information.

PS3037

ERIAL

BACnet

Modbus

Description

Steady Green

Power is applied to the meter.

Flashing Green

The meter is communicating.

Steady Red

Communications failure, or talking with BACnet while the meter is in

Modbus mode.

Flashing Red

The meter is receiving communication on the bus for a meter at

another address.

Table II-6: PS3037 Serial COM LED Signals

PS3037

THERNET

The Ethernet cable has a Link LED on its connector that glows amber when connected to the network

and flashes green during Ethernet traffic.

BACnet/Modbus

Description

Steady Green

Power is applied to the meter.

Flashing Green

The meter is communicating.

Table II-7: PS3037 Ethernet COM LED Signals

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for powerscout 3037












































































































Search results

Summary of Contents for powerscout 3037

Reviews:

Related manuals for powerscout 3037

Brands by name

Popular brands

DENT Instruments powerscout 3037, Operator'S Manual

Search results

Summary of Contents for powerscout 3037

Reviews:

Related manuals for powerscout 3037

Brands by name

Popular brands