DENT Instruments powerscout 3037 Operator'S Manual Download Page 87

Page: 87 / 107

APPENDICES

Appendix A—Additional Wiring Diagrams

Typically, the PowerScout can be wired using any one of the previous setups found in the PowerScout

3037 Wiring Diagrams. The following are less frequently used configurations and will assist you in

properly connecting your PowerScout meter for the desired setup. ALL WIRE COLORS ARE U.S.

STANDARD.

WARNING! DO NOT EXCEED 600VAC PHASE TO PHASE CAT III.

When complete, close the enclosure cover, if equipped.

Attention: Ne pas dépasser une phase à 600VAC CAT III.

Une fois terminé, fermer le covercle, s’il y en a un.

CAUTION:

THE POWERSCOUT

™

METER SHOULD ONLY BE WIRED BY QUALIFIED

PERSONNEL. HAZARDOUS VOLTAGES EXIST.

ATTENTION:

LE POWERSCOUT ™ ne doit être branché QUE par un personnel qualifié.

TENSIONS DANGEREUSES sont présentEs.

DANGER! THE UNENCLOSED POWERSCOUT BOARD REQUIRES EXTRA CAUTION

WHEN CONNECTING. LIFE THREATENING VOLTAGES EXCEEDING 600 VOLTS MAY

EXIST ON THE BOARD. THE RISK OF SERIOUS INJURY OR DEATH SHOULD NOT BE

UNDERESTIMATED.

DANGER! LA PLAQUETTE DE CIRCUITS IMPRIMES SANS COUVERCLE EXIGE UN

REDOUBLEMENT DE PRUDENCE QUAND ON FAIT LA CONNEXION. LES TENSIONS

DEPASSANT 600 VOLTS PEUVENT EXISTER SUR LA PLAQUETTE ET PEUVENT METTRE

LA VIE EN DANGER. LE RISQUE DE BLESSURES GRAVES OU DE MORT NE DOIT PAS

ETRE SOUS-ESTIME.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for powerscout 3037












































































































Search results

Summary of Contents for powerscout 3037

Reviews:

Related manuals for powerscout 3037

Brands by name

Popular brands

DENT Instruments powerscout 3037, Operator'S Manual

Search results

Summary of Contents for powerscout 3037

Reviews:

Related manuals for powerscout 3037

Brands by name

Popular brands