Denso QK30-U, User Manual

Page: 107 / 114

96
meters for multi-line barcode scanning (to be preceded by an ampersand (&))
Syntax Example
Command para
Specified code symbol
EAN/UPC
(EAN-13/EAN-8/UPC-A/UPC-E)
A: cod ra ]]
where,
co
is
A
,
B
, or cifyin
A
EAN- UPC-A
B
EAN-
C
UPC-
C, &A:A49 e [ 1stcha [ 2ndchara
de C
spe g the following:
13/
8
E
&A:A, &A:B, &A:
Inte F)
I[:[[ mini.no.digits x.no.
[ 1stchara ]]]]
&I:6-10C;, &I:;12
rleaved 2of5 (IT
[- ma digits ]][ C ];
[ 2ndchara
Codabar (NW-7)
N[:[ mini.no.digits [ .no.d
[ startstop C ]]
4-8C
- max igits ]]
&N:8AAC, &N:
][
Code 39
M[:[[ mini.no.digits x.no.
[ 1stch chara ]]]]
, &M:;23
[- ma digits ]][ C ];
&M:8-12C;
ara [ 2nd
Code 128
K[:[[ mini.no.digits .no.
[ 1stch chara ]]]]
&K:;34
[- max digits ]];
&K:6-12;,
ara [ 2nd
GS1-128
W[:[[mi digit .no.
[ 1stch chara ]]]]
ni.no. s[-max digits]];
ara [ 2nd
&W:6-12;, &W:;34
Code 93
L[:[[m digit .no.
[ 1stchara [ 2ndchara ]]]]
12;, &L:;34
ini.no. s[-max digits]];
&L:6-
N e minimum and maximum numbe its for s to ollowing condition.
ni.no.digits

max.no.digits
N
ini.no.digits
only m s the scan ead th pecified by
mini.no.digits
.
only is n ed.
N s allowed for multi-line barcode sc
No s the orde ode types specified by
Note 5:
( of S&A:A,&I,&N:C allows the following codes to be scanned.
ote 6: If d for multi-line barcode scanning does not satisfy the scanning condition, the scanner scans it as
a single-line code.
check digit
its, starting with 56
(In ad EAN-13/UPC-A and Code 128 out of the above specifications as a
single-line code, but it cannot read any Code 39 as a single-line code. This is because Code 39 has no scanning
co
that all Code 39 symbols are targets for multi-line scanning.)
ote 1: Th rs of dig bar code be read should satisfy the f
mi
ote 2: Specifying
m
Specifying
max.no.digits
ake
ot allow
ner r e number of digits s
ote 3: The number of line anning is 2 or 3.
te 4: The data output order follow r of c an "S" command.
To specify two or more parameters in a command sequence, separate them with commas (,) as shown below. If any
one of them is wrong, the scanner returns an "NG" response to the host and makes all parameters invalid
Example) Specification
- Multi-line bar codes under the following conditions
1st line: EAN-13/UPC-A
2nd line: ITF with/without a check digit
3rd line: Codabar (NW-7) with a check digit
a bar code specifie N
(Example) Specification of S&A:A12,&M,&K:5-10;56 allows the following codes to be scanned.
- Multi-line bar codes under the following conditions
1st line: EAN-13/UPC-A starting with 12
2nd line: Code 39 with/without a
3rd line: Code 128 of 5 to 10 dig
the above case, the scanner can re
ndition specification so