9
ENGLISH
(2) Rear Panel
!6
Audio output connectors (AUDIO OUT)
!7
Digital audio output connector (OPTICAL)
• Connect using an optical fiber cable (available in
stores).
• Digital data is output from this connector.
!8
Digital audio output connector (COAXIAL)
• Connect using an audio cord. Connect a commercially
available 75
Ω
/ohms pin-plug cord.
• Connect using the included audio video cord.
!9
Video output connector (VIDEO OUT)
• Connect using the included audio video cord.
@0
S-Video output connector (S-VIDEO OUT)
• Connect using an S-Video connection cord (available in
stores).
@1
Component video output connectors
(COMPONENT)
• Connect using video cords (available in stores).
(3) Display
Lights during playback, flashes when the resume play memory function is activated.
Lights in the repeat play mode.
Lights in the still/pause mode.
Lights during playback of
24-bit linear PCM sound.
Lights during playback of
linear PCM sound with a
sampling frequency of 96
kHz.
The title and elapsed track time are
displayed here during playback.
The title/chapter number is displayed here for
DVDs, the track number for video and music CDs.
Lights in the programmed play mode.
Lights during playback of multiple angles discs.
Lights when a DVD is loaded in the disc tray.
DVD
PROG.
ANGLE
96kHz 24bit
6
REMOTE CONTROL UNIT
2
The DVD-2800 can be controlled from a distance using the included remote control unit (RC-546).
(1) Inserting Batteries
q
Remove the remote control unit’s rear cover.
w
Place two R03/AAA batteries in the battery compartment in
the direction indicated by the marks.
e
Close the rear cover.
Cautions On Batteries
• Use R03/AAA batteries in this remote control unit.
• Replace the batteries with new ones approximately once
a year, though this depends on the frequency with which
the remote control unit is used.
• If the remote control unit does not operate from close to
the main unit, replace the batteries with new ones, even
if less than a year has passed.
• The included battery is only for verifying operation.
Replace it with a new battery as soon as possible.
• When inserting the batteries, be careful to do so in the
proper direction, following the
<
and
>
marks in the
remote control unit’s battery compartment.
• To prevent damage or battery fluid leakage:
• Do not use a new battery with an old one.
• Do not use two different types of batteries.
• Do not short-circuit, disassemble, heat or dispose of
batteries in flames.
• Remove the batteries when not planning to use the
remote control unit for a long period of time.
• If the batteries should leak, carefully wipe off the fluid
from the inside of the battery compartment, then insert
new batteries.
(2) Using the Remote Control Unit
30
°
30
°
Approx. 7 meters
• When operating the remote control unit, point it at
the remote control sensor as shown on the
diagram.
• The remote control unit can be used from a direct
distance of approximately 7 meters. This distance
will be shorter, however, if there are obstacles in
the way or if the remote control unit is not pointed
directly at the remote control sensor.
• The remote control unit can be operated at a
horizontal angle of up to 30° with respect to the
remote control sensor.
NOTES:
• It may be difficult to operate the remote control unit if the remote control sensor is exposed to direct sunlight or strong
artificial light.
• Do not press buttons on the main unit and on the remote control unit at the same time. Doing so will result in malfunction.
@2
21-pin SCART terminal (AV 1)
(For only European model)
• Connect using a 21-pin SCART cable (available in
stores).
@3
Control input connector
(ROOM TO ROOM / IN)
• This is the input connector for wired remote control.
Consult your DENON dealer if you wish to use this
connector.
@4
Control output connector
(ROOM TO ROOM / OUT)
• This is the output connector for wired remote control.
Consult your DENON dealer if you wish to use this
connector.
@5
Power input (AC IN)
• Connect to AC power supply using the included AC cord.
NOTE:
®
,HDCD
®
, High Definition Compactible Dgital
®
and
Pacific Microsonics
TM
are either registered trademarks or
trademarks of Pacific Microsonics, Inc. in the United States
and/or other countries. HDCD system manufactured under
license from Pacific Microsonics, Inc. This product is covered
by one or more of the following: In the USA: 5,479,168,
5,683,074, 5,640,161, 5,808,574, 5,838,274, 5,854,600,
5,864,311, 5,872,531, and in Australia: 669114. Other patents
pending.
