11
Basic version
Advanced version
Information
ENGLISH
Simple version
Error messages
An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc.
If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.
NOTE
Be sure to turn off the power before checking speaker connections.
Examples
Error details
Measures
$8'<66(<$8726(783
7KHVXEZRRIHU·VOHYHOLVWRRKLJKRUORZ3OHDVHVHOHFW´6:
/HYHO0DWFKLQJµDQGDGMXVWWKHOHYHORI\RXUVXEZRRIHUXQLW
,I\RXGRQRWZDQWWRXVHWKH
VXEZRRIHUVHOHFW´6NLSµ
6NLS
&DXWLRQ
6:/HYHO0DWFKLQJ
• Correct measurement is not possible due to
inappropriate subwoofer volume.
• When using a subwoofer with built-in
amplifi er (active type), use “SW Level
Matching” to adjust the subwoofer volume
(
v
page 11 “Subwoofer level error message
and how to adjust”).
• When using a subwoofer without a built-in
amplifi er, select “Skip”, and then press
ENTER
.
$8'<66(<$8726(783
5(7851
&DQFHO
1RPLFURSKRQHRUVSHDNHU
5HWU\
&DXWLRQ
• The connected setup microphone is broken,
or a device other than the supplied setup
microphone is connected.
• Not all speakers could be detected.
• The front L speaker was not properly
detected.
• Connect the included setup microphone to
the SETUP MIC jack of this unit.
• Check the speaker connections.
$8'<66(<$8726(783
5(7851
&DQFHO
$PELHQWQRLVHLVWRRKLJK
RU/HYHOLVWRRORZ
5HWU\
&DXWLRQ
• There is too much noise in the room for
accurate measurements to be made.
• Speaker or subwoofer sound is too low for
accurate measurements to be made.
• Either turn off any device generating noise
or move it away.
• Perform again when the surroundings are
quieter.
• Check the speaker installation and the
direction in which the speakers are facing.
• Adjust the subwoofer’s volume.
$8'<66(<$8726(783
5(7851
)URQW5
1RQH
&DQFHO
&DXWLRQ
5HWU\
• The displayed speaker could not be detected. • Check the connections of the displayed
speaker.
$8'<66(<$8726(783
5(7851
)URQW/
3KDVH
&DQFHO
&DXWLRQ
5HWU\
6NLS
• The displayed is connected with the
polarities reversed.
• Check the polarities of the displayed
speaker.
• For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure the connection is
correct, press
ui
to select “Skip”, then
press
ENTER
.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confi rm the setting
Return to previous menu
Subwoofer level error message and how to adjust
The optimal level of each subwoofer channel for Audyssey
Auto Setup measurement is 75 dB. During subwoofer level
measurement (“Set up speakers (Audyssey® Auto Setup),
STEP2
Detection & Measurement
” (
v
page 9), 6 –
q
), an error
message is displayed when one level of subwoofers is outside the
72 – 78 dB range. When using a subwoofer with built-in amplifi er
(active type), adjust the subwoofer volume so that the subwoofer
level is within the 72 to 78 dB range.
1
6HOHFW³6:/HYHO0DWFKLQJ´DQGWKHQSUHVV
ENTER
$8'<66(<$8726(783
5(7851
7KHVXEZRRIHU·VOHYHOLVWRRKLJKRUORZ3OHDVHVHOHFW´6:
/HYHO0DWFKLQJµDQGDGMXVWWKHOHYHORI\RXUVXEZRRIHUXQLW
,I\RXGRQRWZDQWWRXVHWKH
VXEZRRIHUVHOHFW´6NLSµ
3URFHHGWRVXEZRRIHUYROXPHDGMXVWPHQWLWHP
(QWHU
&DQFHO
6NLS
&DXWLRQ
6:/HYHO0DWFKLQJ
