manualshive.com logo in svg

Dell XPS 8900, Service Manual, Page: 86 / 107

Share
Download
Dell XPS 8900 Service Manual Download Page 86

Replacing the processor fan 

and heat-sink assembly

WARNING: Before working inside your computer, read the safety 
information that shipped with your computer and follow the steps in 

Before working inside your computer

. After working inside your 

computer, follow the instructions in 

After working inside your 

computer

. For more safety best practices, see the Regulatory 

Compliance home page at www.dell.com/regulatory_compliance. 

 

Procedure

NOTE: The original thermal grease can be reused if the original 

processor and heat-sink assembly are reinstalled together.

CAUTION: If either the processor or the heat-sink assembly is 

replaced, use the thermal grease provided in the kit to make sure that 

thermal conductivity is achieved.

1 

Place the processor fan and heat-sink assembly over the processor.

2 

Align the captive screws on the processor fan heat-sink assembly with 

the screw holes on the system board.

3 

Tighten the captive screws that secure the processor fan and heat-sink 

assembly to the system board.

4 

Connect the processor-fan cable to the system board.
For more information, see “

System-board components

”.

Post-requisites

Replace the 

computer cover

.

86

Summary of Contents for XPS 8900












































































































Reviews:

No comments