Dell PowerEdge 700 Installation And Troubleshooting Manual Download Page 81

Page: 81 / 94

For instructions, see the documentation that accompanied the drive.

Remove the bezel. See "

Removing the Bezel

" in "Troubleshooting Your System."

Open the hard-drive carrier handle. See

Figure 7

-11

Insert the hard-drive carrier into the drive bay. See

Figure 7

-11

Close the hard-drive carrier handle to lock it in place.

Install the bezel. See "

Installing the Bezel

" in "Troubleshooting Your System."

Install any required SCSI device drivers.

Run the SCSI controllers tests and the hard drive tests in the system diagnostics. See "

Running System Diagnostics

If the hard drive fails the hard drive tests or does not operate properly, see "

Getting Help

Installing a RAID Controller Card

See "

Installing an Expansion Card

" in "Installing System Components" for instructions about installing the card.

Back to Contents Page

NOTICE:

Do not insert a hard-drive carrier and attempt to lock its handle next to a partially installed carrier. Doing so can damage the partially installed

carrier's shield spring and make it unusable. Ensure that the adjacent drive carrier is fully installed.

NOTE:

Install a RAID controller card in expansion slot 3, 4, or 5. If you install both a RAID controller card and an Ultra 3 SCSI controller card, install the

RAID controller card in expansion slot 5. See

Figure A

-3

to identify the expansion slots.

Summary of Contents for PowerEdge 700































































































Search results

Summary of Contents for PowerEdge 700

Reviews:

Related manuals for PowerEdge 700

Brands by name

Popular brands

Dell PowerEdge 700, Installation And Troubleshooting Manual

Search results

Summary of Contents for PowerEdge 700

Reviews:

Related manuals for PowerEdge 700

Brands by name

Popular brands