Dell PowerEdge 700 Installation And Troubleshooting Manual Download Page 67

Page: 67 / 94

Unpack the expansion card, and prepare it for installation.

For instructions, see the documentation that accompanied the card.

Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

Remove the bezel. See "

Removing the Bezel

" in "Troubleshooting Your System."

Lay the system on its right side.

Remove the cover. See "

Removing the Cover

" in "Troubleshooting Your System."

Remove the filler bracket from the expansion slot.

Install the expansion card. See

Figure 6

-9

Position the expansion card so that the card-edge connector aligns with the expansion- card connector on the system board.

Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated.

Install the screw that secures the expansion-card bracket to the back panel.

Connect any cables that should be attached to the card.

See the documentation that accompanied the card for information about its cable connections.

Install the cover. See "

Replacing the Cover

" in "Troubleshooting Your System."

10.

Stand the system upright.

11.

Install the bezel. See "

Installing the Bezel

" in "Troubleshooting Your System."

12.

Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

13.

Install any device drivers required for the card as described in the documentation for the card.

Figure 6-9. Removing and Installing an Expansion Card

Removing an Expansion Card

Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

Remove the bezel. See "

Removing the Bezel

" in "Troubleshooting Your System."

Lay the system on its right side.

Remove the cover. See "

Removing the Cover

" in "Troubleshooting Your System."

Disconnect any cables attached to the card.

Remove the expansion card (see

Figure 6

-9

Remove the screw that secures the expansion-card bracket to the back panel.

CAUTION:

See your

System Information Guide

for complete information about safety precautions working inside the computer and protecting

against electrostatic discharge.

CAUTION:

See your

System Information Guide

for complete information about safety precautions working inside the computer and protecting

against electrostatic discharge.

Summary of Contents for PowerEdge 700































































































Search results

Summary of Contents for PowerEdge 700

Reviews:

Related manuals for PowerEdge 700

Brands by name

Popular brands

Dell PowerEdge 700, Installation And Troubleshooting Manual

Search results

Summary of Contents for PowerEdge 700

Reviews:

Related manuals for PowerEdge 700

Brands by name

Popular brands