Dell PowerEdge 700 Installation And Troubleshooting Manual Download Page 47

Page: 47 / 94

Install the bezel. See "

Installing the Bezel

10.

Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

If the problem persists, see "

Getting Help

Troubleshooting System Cooling Problems

Problem

Cooling fan is not operating properly.

Systems management software issues a fan-related error message.

Action

Ensure that none of the following conditions exist:

Ambient temperature is too high.

Front and back external airflow is obstructed.

Cables inside the system obstruct airflow.

An individual cooling fan has failed. See "

Troubleshooting a Fan

Troubleshooting a Fan

Problem

Systems management software issues a fan-related error message.

Action

Run the appropriate online diagnostic test. See "

Using Server Administrator Diagnostics

" in "Running System Diagnostics."

Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

Remove the bezel. See "

Removing the Bezel

Lay the system on its right side.

Remove the cover. See "

Removing the Cover

Ensure that the fan cables are properly connected to the fan connectors on the system board.

To identify the system board connectors, see

Figure A

-3

Replace the cover. See "

Replacing the Cover

Stand the system upright.

Install the bezel. See "

Installing the Bezel

10.

Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

If the problem persists, replace the faulty fan. See "

System Fans

" in "Installing System Options."

If the problem is not resolved after a replacement fan is installed, see "

Getting Help

CAUTION:

See your

System Information Guide

for complete information about safety precautions, working inside the computer, and protecting

against electrostatic discharge.

Summary of Contents for PowerEdge 700































































































Search results

Summary of Contents for PowerEdge 700

Reviews:

Related manuals for PowerEdge 700

Brands by name

Popular brands

Dell PowerEdge 700, Installation And Troubleshooting Manual

Search results

Summary of Contents for PowerEdge 700

Reviews:

Related manuals for PowerEdge 700

Brands by name

Popular brands