Dell PowerEdge 700 Installation And Troubleshooting Manual Download Page 56

Page: 56 / 94

Error message indicates a processor problem.

A heat sink is not installed for the processor.

Action

Ensure that you are running the latest BIOS version.

You can download the latest BIOS version from the Dell Support website at

support.dell.com

Run the appropriate online diagnostics test. See "

Using Server Administrator Diagnostics

" in "Running System Diagnostics."

Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

Remove the bezel. See "

Removing the Bezel

Lay the system on its right side.

Remove the cover. See "

Removing the Cover

Remove the cooling shroud. See "

Removing the Cooling Shroud

" in "Installing System Options."

Ensure that the processor and heat sink are properly installed. See "

Replacing the Processor

" in "Installing System Options."

Install the cooling shroud. See "

Installing the Cooling Shroud

" in "Installing System Options."

10.

Install the cover. See "

Replacing the Cover

11.

Stand the system upright.

12.

Install the bezel. See "

Installing the Bezel

13.

Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

14.

Run

Quick Tests

in the system diagnostics. See "

Running System Diagnostics

If the tests fail or the problem persists, see "

Getting Help

Back to Contents Page

CAUTION:

See your

System Information Guide

for complete information about safety precautions, working inside the computer, and protecting

against electrostatic discharge.

Summary of Contents for PowerEdge 700































































































Search results

Summary of Contents for PowerEdge 700

Reviews:

Related manuals for PowerEdge 700

Brands by name

Popular brands

Dell PowerEdge 700, Installation And Troubleshooting Manual

Search results

Summary of Contents for PowerEdge 700

Reviews:

Related manuals for PowerEdge 700

Brands by name

Popular brands