Dell P152G Service Manual Download Page 82

Page: 82 / 102

NOTE:

For models shipped with a USB Type-C port, a USB Type-C bracket is secured to the system board with single

(M2x3.5) screw. The bracket is bundled with the system board as a service part and MUST NOT be removed from the
system board.

4. Remove the single (M2x2) screw that secures the system board to the palm-rest.
5. Carefully lift the system board away from the chassis.

Installing the system board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image indicates the connectors on your system board:

1. Fan connector

2. I/O board FFC connector

3. eDP connector

4. DC-in port connector

5. Memory modules

6. Keyboard FFC connector

7. Keyboard-backlight FFC connector

8. Battery connector

9. Touchpad FFC connector

10. Hard drive FFC connector

11. Wireless connector

12. Speaker cable connector

13. Solid-state drive connector

The following images indicate the location of the system board and provide a visual representation of the installation procedure.

Removing and installing components

Summary of Contents for P152G







































































































Search results

Summary of Contents for P152G

Reviews:

Related manuals for P152G

Brands by name

Popular brands

Dell P152G, Service Manual

Search results

Summary of Contents for P152G

Reviews:

Related manuals for P152G

Brands by name

Popular brands