background image

If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing,
bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical
support for assistance. See 

www.dell.com/contactdell

.

Always purchase genuine batteries from 

www.dell.com

 or authorized Dell partners and resellers.

Swollen batteries should not be used and should be replaced and disposed properly. For guidelines on how to
handle and replace swollen Lithium-ion batteries, see 

Handling swollen Lithium-ion batteries

.

Removing the battery

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

SD card

.

3. Remove the 

base cover

.

About this task

The following image indicates the location of the 4-cell battery and provides a visual representation of the removal procedure.

Steps

1. Disconnect the battery cable from the system board, if applicable.
2. Remove the five (M2x3) screws that secure the battery to the palm-rest and keyboard assembly.

NOTE:

 A 3-cell battery has three (M2x3) screws that secure the battery to the palm-rest and keyboard assembly.

3. Remove the battery from the palm-rest and keyboard assembly.

Installing the battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

Removing and installing components

21

Summary of Contents for P152G







































































































Reviews: