manualshive.com logo in svg

Dell P152G, Service Manual, Page: 74 / 102

Share
Download
Dell P152G Service Manual Download Page 74

Display cover and antenna assembly

Replacement of the display cover and antenna assembly

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

SD card

.

3. Remove the 

base cover

.

4. Remove the 

wireless card

.

5. Remove the 

display assembly

.

6. Remove the 

display hinge caps

.

7. Remove the 

display bezel

.

8. Remove the 

display hinges

.

9. Remove the 

display panel

.

10. Remove the eDP cable (

plastic

) or (

aluminum

), whichever applicable.

About this task

The following image indicates the location of the display cover and antenna assembly and provides a visual representation of the
removal procedure.

Figure 1. Display cover (plastic chassis)

NOTE:

 The display cover and antenna assembly cannot be further disassembled. If the WLAN antennas are malfunctioning

and needs replacement, replace the entire display cover and antenna assembly.

74

Removing and installing components

Summary of Contents for P152G







































































































Reviews:

No comments