Dell P152G Service Manual Download Page 65 | Manualshive

Page: 65 / 102

background image

Steps

1. Place the display panel and display assembly on a clean and flat surface.
2. Connect the display cable to the connector on the display panel and close the latch.
3. Adhere the tape to secure the display-cable connector latch to the display panel.
4. Lift and rotate the display panel, and then place the display panel on the display assembly.
5. Place the display bezel on the display assembly.
6. Align the tabs on the display bezel to the slots on the display assembly.
7. Press down on the display bezel and snap the display bezel in place.
8. Replace the two (M2x2) screws to secure the display panel to the back cover.

Next steps

1. Install the

.

2. Install the

3. Install the

.

4. Install the

display assembly

.

5. Install the

.

6. Install the

7. Install the

.

8. Install the

.

9. Follow the procedure in

After working inside your computer

.

eDP cable

Removing the eDP cable (Plastic)

Prerequisites

1. Follow the procedure in

Before working inside your computer

.

2. Remove the

.

3. Remove the

.

4. Remove the

.

5. Remove the

.

6. Remove the

.

7. Remove the

display assembly

.

8. Remove the

9. Remove the

10. Remove the

.

11. Remove the

.

About this task

The following image indicates the location of the eDP cable (in a system shipped with plastic chassis) and provides a visual
representation of the removal procedure.

Removing and installing components

65

«
...
63
64
65
66
67
...
»

Summary of Contents for P152G







































































































Reviews:

No comments

Related manuals for P152G

Brand: Hena Pages: 7

S7220 - LifeBook - Core 2 Duo 2.4 GHz

Brand: Fujitsu Pages: 208

Brand: Bluewave Pages: 11

Brand: Kogan Pages: 49

Brand: HYPA Pages: 8

Brand: Sharper Image Pages: 9

Brand: HP Compaq Pages: 129

Brand: Xbrand Pages: 2

Brand: Tadpole Pages: 116

Extensa 450 Series

Brand: Texas Instruments Pages: 100

Brand: XMG Pages: 38

VERSA LXI#RELEASE NOTES

Brand: NEC Pages: 10

Brand: Acer Pages: 22

Blade RZ09-02385

Brand: Razer Pages: 33

Brand: Panasonic Pages: 20

Toughbook CF-T5MWETABM

Brand: Panasonic Pages: 2

Brand: Samsung Pages: 158

Toughbook CF-W5LCEZZBM

Brand: Panasonic Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands