Dell P152G Service Manual Download Page 47 | Manualshive

Page: 47 / 102

background image

3. Open the display hinges at an angle of 90 degrees, and place the system on a flat surface.
4. Remove the display assembly from the palm-rest and keyboard assembly.

NOTE:

For systems with an aluminum chassis, the display assembly is a Hinge-Up Design (HUD) assembly and cannot

be further disassembled once it is removed from the bottom chassis. If any components in the display assembly
malfunction and needs replacement, the entire display assembly has to be replaced.

Installing the display assembly (Aluminum)

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following images indicate the location of the display assembly and provide a visual representation of the installation
procedure.

Removing and installing components

47

«
...
45
46
47
48
49
...
»

Summary of Contents for P152G







































































































Reviews:

No comments

Related manuals for P152G

Brand: Acer Pages: 9

TravelMate 2200

Brand: Acer Pages: 106

Brand: Acer Pages: 9

Brand: Acer Pages: 102

Brand: Acer Pages: 102

Aspire Timeline 4810TZ

Brand: Acer Pages: 148

Predator Triton 500

Brand: Acer Pages: 9

Brand: Redfox Pages: 21

Brand: Acer Pages: 73

Latitude 7400 2-in-1

Brand: Dell Pages: 46

Brand: Dell Pages: 79

Brand: Dell Pages: 81

Brand: Dell Pages: 35

Brand: Dell Pages: 29

Brand: Dell Pages: 23

Brand: Dell Pages: 77

Latitude 7400-01

Brand: Dell Pages: 18

Latitude 7400 2-in-1

Brand: Dell Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands