Dell P152G Service Manual Download Page 36

Page: 36 / 102

Steps

1. Place the heat sink on the system board.
2. Tighten the seven (M2x3) captive screws that secure the heat sink to the system board.

NOTE:

Tighten the captive screws in the sequential order mentioned on the heat sink [7>6>5>4>3>2>1].

NOTE:

The number of screws varies depending on the configuration ordered.

Next steps

1. Install the

base cover

2. Install the

SD card

3. Follow the procedure in

After working inside your computer

I/O daughter board FFC

Removing the Input/Output daughter board FFC

Prerequisites

1. Follow the procedure in

Before working inside your computer

2. Remove the

SD card

3. Remove the

base cover

4. Remove the

fan

About this task

The following image indicates the location of the Input/Output daughter board FFC and provides a visual representation of the
removal procedure.

Removing and installing components

Summary of Contents for P152G







































































































Search results

Summary of Contents for P152G

Reviews:

Related manuals for P152G

Brands by name

Popular brands

Dell P152G, Service Manual

Search results

Summary of Contents for P152G

Reviews:

Related manuals for P152G

Brands by name

Popular brands