Dell P152G Service Manual Download Page 58

Page: 58 / 102

4. Pry open the display bezel from the inner edge at the bottom side of the display assembly.
5. Lift and remove the display bezel from the display assembly.

Installing the display bezel

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

NOTE:

This procedure is applicable for systems with plastic chassis.

About this task

The following image indicates the location of the display bezel and provides a visual representation of the installation procedure.

Steps

Align the display bezel with the display back-cover and antenna assembly, and then gently snap the display bezel into place.

Next steps

1. Install the

2. Install the

3. Install the

4. Install the

5. Install the

Removing and installing components

Summary of Contents for P152G







































































































Search results

Summary of Contents for P152G

Reviews:

Related manuals for P152G

Brands by name

Popular brands

Dell P152G, Service Manual

Search results

Summary of Contents for P152G

Reviews:

Related manuals for P152G

Brands by name

Popular brands