Dell P152G Service Manual Download Page 31

Page: 31 / 102

Fan

Removing the fan

Prerequisites

1. Follow the procedure in

Before working inside your computer

2. Remove the

SD card

3. Remove the

base cover

About this task

The following images indicate the location of the fan and provide a visual representation of the removal procedure.

Steps

1. Disconnect the fan cable from the system board.
2. Remove the two (M2x5) screws that secure the fan to the palm-rest and keyboard assembly.
3. Lift the fan from the palm-rest and keyboard assembly.

Installing the fan

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following images indicate the location of the fan and provide a visual representation of the installation procedure.

Removing and installing components

Summary of Contents for P152G







































































































Search results

Summary of Contents for P152G

Reviews:

Related manuals for P152G

Brands by name

Popular brands

Dell P152G, Service Manual

Search results

Summary of Contents for P152G

Reviews:

Related manuals for P152G

Brands by name

Popular brands