DeLaval VMS 2008, Instruction Book

Page: 182 / 206

Troubleshooting
DeLaval voluntary milking system VMS
94897201.pdf 2007-12-18
M m Alarm text Type Meaning Action M m Alarm text Type Meaning Action
3 107 Air inlet blocked User
notification One of the DeLaval milk meter
MM25 has sent a message to the
milking software that an air-inlet
may be blocked. Check the air-inlet. 3 107 Air inlet blocked User
notification One of the DeLaval milk meter
MM25 has sent a message to the
milking software that an air-inlet
may be blocked. Check the air-inlet.
3 108 Invalid
Milksampler config Stop alarm Some parameters concerning the
milk sampler are invalid. Contact service engineer.
Service engineer only:
The values specifying the sample tray
may be incorrect.
The sample tray in the milk sampler
differs some from country to country. A
list of parameters for the different trays
should be delivered with the milk
sampler. The parameters are entered
in the management software (VMS
Config). 3 108 Invalid
Milksampler config Stop alarm Some parameters concerning the
milk sampler are invalid. Contact service engineer.
Service engineer only:
The values specifying the sample tray
may be incorrect.
The sample tray in the milk sampler
differs some from country to country. A
list of parameters for the different trays
should be delivered with the milk
sampler. The parameters are entered
in the management software (VMS
Config).
3 114 Milkmeter ...
conductivity ... out
of range (... - ...) Deviation The milk meter provides
physiologically unreasonable
conductivity values.
Values below 3000 might indicate
deposits on the
conductivity-measuring electrodes,
while values above 10000 may
point to a faulty milk meter. Always carry out the following general
steps when the milk meters cause
alarms:
- Check that the active-air inlets can
admit air (see procedure in instruction
book, chapter “maintenance”).
- Start a system cleaning to remove
possible deposits on the milk meter’s
electrodes.
- If the problem persists, call service
engineer. 3 114 Milkmeter ...
conductivity ... out
of range (... - ...) Deviation The milk meter provides
physiologically unreasonable
conductivity values.
Values below 3000 might indicate
deposits on the
conductivity-measuring electrodes,
while values above 10000 may
point to a faulty milk meter. Always carry out the following general
steps when the milk meters cause
alarms:
- Check that the active-air inlets can
admit air (see procedure in instruction
book, chapter “maintenance”).
- Start a system cleaning to remove
possible deposits on the milk meter’s
electrodes.
- If the problem persists, call service
engineer.
Service engineer only:
- Check that nothing obstructs the
passage through the milk meter.
- Check the power supply to the milk
meter. Service engineer only:
- Check that nothing obstructs the
passage through the milk meter.
- Check the power supply to the milk
meter.
3 115 Conductivity differ
(...) too much (...)
between meters Deviation The values from one milk meter
differ significantly from the others.
It is not specified which meter it is
that differs from the others, only
that the difference exist. It is not specified which meter it is that
differs from the others, only that the
difference exist. 3 115 Conductivity differ
(...) too much (...)
between meters Deviation The values from one milk meter
differ significantly from the others.
It is not specified which meter it is
that differs from the others, only
that the difference exist. It is not specified which meter it is that
differs from the others, only that the
difference exist.
3 116 Milkmeter ...
conductivity (...)
differ (...) from
other meters Deviation One of the milk meters give values
that differ significantly from the
ones provided yesterday.
The alarm is issued if the
difference appears for only one
milk meter. See the general steps for alarm major
code 3, minor code 114 above. 3 116 Milkmeter ...
conductivity (...)
differ (...) from
other meters Deviation One of the milk meters give values
that differ significantly from the
ones provided yesterday.
The alarm is issued if the
difference appears for only one
milk meter. See the general steps for alarm major
code 3, minor code 114 above.
3 117 Milking self test
failed Stop alarm Selftest from milking system failed.
Vacuum level indicate bad
vacuum in some milktube. Make sure system has vacuum. Call
service technician if problem remains. 3 117 Milking self test
failed Stop alarm Selftest from milking system failed.
Vacuum level indicate bad
vacuum in some milktube. Make sure system has vacuum. Call
service technician if problem remains.
3 118 FF meter %...f is
having problems
measuring blood Deviation The average value of blood is too
high (over 600 ppm). Check the air inlets and run a system
cleaning. If that doesn’t solve the
problem, check if something is stuck
inside the meter. If the problems
persists call service engineer. 3 118 FF meter %...f is
having problems
measuring blood Deviation The average value of blood is too
high (over 600 ppm). Check the air inlets and run a system
cleaning. If that doesn’t solve the
problem, check if something is stuck
inside the meter. If the problems
persists call service engineer.
3 119 Many milkings with
high blood value Deviation There are more then 10 milkings
in a row with a blood level above
800 ppm. Check the air inlets and run a system
cleaning. If that doesn’t solve the
problem, check if something is stuck
inside the meter. If the problems
persists call service engineer. 3 119 Many milkings with
high blood value Deviation There are more then 10 milkings
in a row with a blood level above
800 ppm. Check the air inlets and run a system
cleaning. If that doesn’t solve the
problem, check if something is stuck
inside the meter. If the problems
persists call service engineer.
174(198)