Del ozone TrioPure 25 Installation And Operation Manual Download Page 12

Page: 12 / 31

TrioPure

Sanitation System

DEL Ozone · San Luis Obispo, CA 93401 · USA · 800-676-1335 · Fax: 805-541-8459

2e-3 Plumbing Configurations (Continued)

Figure 7

- (New Pool, Pool Spa Combination, No ICS, Solar):

· Manifold to be plumbed between the filter and heater.

· TrioPure

return port of the bypass manifold capped off.

· Return from TrioPure

plumbed to a dedicated 2 c

m (¾”) r

eturn to the lowest point of the pool.

· An automated shut-off valve needs to be put in the line between the bypass manifold and the TrioPure

, which is tied into

the Pool/Spa control system, and shuts off water to the TrioPure when in spa mode.

- If this is overlooked, the TrioPure will pump water from the spa into the pool, when in spa mode.

- To minimize the size of ozone bubbles, use a dispersion cap or main drain cover. This may require a stub-up to the

appropriate size for the fitting.

· Del recommends installing 2 cm (¾”) ball valves on the inlet and outlet of the Triopure to facilitate Salt Cell removal for

cleaning and a ball valve after the Bypass Manifold to control water flow through the Salt Cell.

Figure 8 -

(Existing Pool, Pool Spa Combination, No ICS, Solar):

· Manifold to be plumbed between the filter and heater.

· TrioPure

return port of the bypass manifold capped off.

· Return from TrioPure

plumbed into a tee in the main pool return after the 3 way valve that diverts water between the pool

and spa.

· An automated shut-off valve needs to be put in the line between the bypass manifold and the TrioPure

, which is tied into

the Pool/Spa control system, and shuts off water to the TrioPure

when in spa mode.

- If this is overlooked, the TrioPure will pump water from the spa into the pool, when in spa mode.

· Del recommends installing 2 cm (¾”) ball valves on the inlet and outlet of the Triopure to facilitate Salt Cell removal for

cleaning and a ball valve after the Bypass Manifold to control water flow through the Salt Cell.

SPA

POOL

SOLAR

HEATER

POOL

SPA

SOLAR

HEATER

TrioPure

Summary of Contents for TrioPure 25
































Search results

Summary of Contents for TrioPure 25

Reviews:

Related manuals for TrioPure 25

Brands by name

Popular brands

Del ozone TrioPure 25, Installation And Operation Manual

Search results

Summary of Contents for TrioPure 25

Reviews:

Related manuals for TrioPure 25

Brands by name

Popular brands