Del ozone TrioPure 25 Installation And Operation Manual Download Page 24

Page: 24 / 31

Step 6

- With the chlorinator cell now mechanically detached,

access the two small electrical connectors for the flow switch

and the temperature sensor and disconnect these connectors

from chlorinator cell. The connectors have a locking feature

that must be raised to separate the connector plug and socket.

Remove the chlorinator cell from the TrioPure

enclosure.

5d-4 Air Filters

The TrioPure

has screen filters located at both the cooling fan

air intake on the right side of the enclosure and the air exhaust

at the bottom of the enclosure (

Figure 26

). The screen filters are

intended to keep insects and debris out of the TrioPure

unit.

Allowing these screen filters to become clogged could result in

the TrioPure

shutting down to protect from overheating.

Annual inspection and

cleaning of the screen

filters is recommended

as follows:

TrioPure

Sanitation System

DEL Ozone · San Luis Obispo, CA 93401 · USA · 800-676-1335 · Fax: 805-541-8459

Step 5

- With one hand supporting the chlorinator cell in the middle, unscrew the right hand side attachment knob. As this knob

is unscrewed, the chlorinator cell will lower. Use caution and do not allow the weight of the chlorinator cell to stress the wires on

the electrical connectors.

2) Disconnect quick

disconnect fitting

4) Remove attachment shaft

5) Remove chlorinator cell by turn-

ing knob counterclockwise

1) Turn power off

6) Disconnect the two small

electrical connectors

3) Remove the two electrical

connectors

Figure 25

Figure 26

Figure 27

Figure 28

Air In

take

Air Intake Screen

Filter:

Turn off power

to the TrioPure

. Remove

the cover by sliding

the cover up (

Figure

). Once the cover is

removed, visually check

the filter for debris. If the

filter appears to require

cleaning, carefully remove plastic filter keeper (

Figure 28

) by lightly

prying it out. Remove the screen filter and clean it. Replace filter,

keeper and cover.

Air Exhaust

Air Exhaust Screen Filter:

The Air Exhaust filter should

typically not require servicing.

After removing the Chlorinator

Cell (See Section 5D-4), visu-

ally check the filter for debris.

If the filter appears to require

cleaning, then remove plastic

filter keeper by lightly prying it

out. Remove the screen filter,

clean and replace.

Lift (slide)

cover up for

filter access.

Lightly pry

here with

coin or

screwdriver

to remove

plastic filter

keeper.

Summary of Contents for TrioPure 25
































Search results

Summary of Contents for TrioPure 25

Reviews:

Related manuals for TrioPure 25

Brands by name

Popular brands

Del ozone TrioPure 25, Installation And Operation Manual

Search results

Summary of Contents for TrioPure 25

Reviews:

Related manuals for TrioPure 25

Brands by name

Popular brands