Del ozone TrioPure 25 Installation And Operation Manual Download

Page: 1 / 31

TRIOPURE-25 CHLORINE GENERATOR CONTROLS BACTERIA AND

ALGAE IN DOMESTIC SWIMMING POOLS (SPA) WATERS

A MAXIMUM OF 57,000 L OF WATER CAN BE TREATED WITH ONE

TRIOPURE-25.

MAXIMUM OUTPUT OF HYPOCHLOROUS ACID EQUIVALENT TO 0.20 Kg

OF FREE AVAILABLE CHLORINE PER DAY

FOR SWIMMING POOLS, A MINIMUM OF 1 ppm OF FREE AVAILABLE

CHLORINE MUST BE MAINTAINED AND FOR SPAS A MINIMUM OF 3 ppm

OF FREE AVAILABLE CHLORINE MUST BE MAINTAINED

READ THE LABEL AND OPERATING MANUAL BEFORE USING

KEEP OUT OF REACH OF CHILDREN

REGISTRATION N

UMBER

28566

PEST CONTROL PRODUCT

ACT

DEL OZONE, 3428 BULLOCK LANE, SAN LUIS OBISPO, CA 93401

WARNING: OPERATING THE TRIOPURE-25 WITHOUT WATER FLOW

THROUGH THE CELL CAN CAUSE A BUILD UP OF FLAMMABLE GASES

WHICH CAN RESULT IN FIRE OR EXPLOSION.

LABEL FOR THE TRIOPURE-25

ENGLISH

TRIOPURE-25 REPLACEMENT CELL

REPLACEMENT CELL FOR THE CHLORINE GENERATING DEVICE TRIOPURE-25

REGISTRATION NUMBER 28566,

PEST CONTROL PRODUCTS ACT

. THIS CELL MUST BE USED

ON THIS MODEL OF CHLORINE GENERATING DEVICE

READ THE LABEL, THE INSTALLATION MANUAL AND OPERATION MANUAL OF THE CHLORINE

GENERATING DEVICE TRIOPURE-25 BEFORE USING

DEL OZONE, 3428 BULLOCK LANE, SAN LUIS OBISPO, CA 93401

LABEL FOR THE TRIOPURE-25

REPLACEMENT CELLS

ENGLISH

1-800-676-1335

09-JUL-2007

3580 Sueldo Street

05-JAN-2009 2009-0003 Notification:
Change in Registrant Address

Notification Change

Summary of Contents for TrioPure 25
































Search results

Summary of Contents for TrioPure 25

Reviews:

Related manuals for TrioPure 25

Brands by name

Popular brands

Del ozone TrioPure 25, Installation And Operation Manual

Search results

Summary of Contents for TrioPure 25

Reviews:

Related manuals for TrioPure 25

Brands by name

Popular brands