manualshive.com logo in svg

DeDietrich IX 145-110, Installation And Service Manual

Share
Download
DeDietrich IX 145-110 Installation And Service Manual Download Page 60

8.3.2 

Checking the electrical connections

1. Check for the presence of the recommended circuit breaker.

2. Check the electrical connection to the mains.

3. Check the connection of the sensors.

4. Check the position of the sensors. Respect the distance of the 

sensors according to the power.

5. Check the connection of the circulating pump(s).

6. Check the connection of the optional equipment.

7. Check the length of the cables and that they are firmly secured in the 

cable clamps.

8.3.3 

Checking the hydraulic circuit

1. Check the siphon, which must be completely filled with water.

2. Check that there are no leaks on the boiler's hydraulic connections.

3. Check the pressure in the expansion vessel before filling the system.

8.3.4 

First time commissioning

When commissioning the boiler for the first time, the control panel needs 

to be synchronised with the boiler. The default setting for the control panel 

is English.

1. Press the  button for 5 seconds.

Synchronisation between the boiler and the control panel starts up 

and shows its progress from 1% to 100%. Synchronisation may take 

several minutes.

2. Select the language.

3. Set the date and time.

For more information, see

Setting the date and time, page 87

Selecting the language, page 87

8.4 

Gas settings

8.4.1 

Configuring the fan speed

The boiler's fan speed has to be configured according to gas type before 

the gas valve is set.

1. Go to the installer parameters.
2. Select the Boiler Settings menu by turning the 

 button.

3. Confirm the menu selection by pressing the   button.

4. Modify parameter 2441 Fan speed heating max according to the gas 

type. Use the   button to select and modify the parameter.

5. Confirm the setting by pressing the   button.
6. Select the Burner control menu by turning the 

 button.

7. Modify parameters 9512 Required speed ignition, 9524 Required 

speed LF and 9529 Required speed HF according to the gas type. 
Use the   button to select and modify the parameters.

For more information, see

Modifying the installer parameters, page 70

8  Commissioning

60

IX

7702703 - v04 - 05092019

Summary of Contents for IX 145-110





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands