manualshive.com logo in svg

DeDietrich IX 145-110, Installation And Service Manual

Share
Download
DeDietrich IX 145-110 Installation And Service Manual Download Page 102

11  Maintenance

11.1  General

We recommend having the boiler inspected and serviced at regular 

intervals.

Caution

Do not neglect to service the boiler. Contact a qualified 

professional or take out a maintenance contract for the obligatory 

annual servicing of the boiler.

Failure to service the appliance voids the warranty.

The annual service is obligatory pursuant to Decree No. 2009-649 

of 9 June 2009.

Danger of electric shock

Before service work is started, the boiler has to be de-energised 

and secured from accidentally being switched back on.

Caution

Have an inspection carried out and the flues swept at least once a 

year or more, depending on the regulations in force in your 

country.

Caution

Only qualified professionals are authorised to carry out 

maintenance work on the boiler and the heating system.

Caution

After maintenance or repair work, check the entire heating system 

to ensure that there are no leaks.

Caution

Only genuine spare parts may be used.

11.2  Standard inspection and maintenance operations

11.2.1  Performing the annual service

1. Check the outward appearance and tightness of the gaskets on the 

gas circuit and the combustion circuit.

2. Check for any impurities inside the combustion chamber. Use a 

vacuum cleaner for any cleaning work.

3. Check the condition of the insulation in the door and at the bottom of 

the combustion chamber and the condition of the gaskets on the 

combustion chamber door.

4. Check the condition and position of the ignition and flame detection 

electrodes, as well as the condition of the burner and its retaining 

device.

5. Check for any impurities inside the siphon.

6. Dry up as much as possible any water that may have stagnated in the 

bottom of the boiler as the result of a maintenance operation.

7. Check that there are no obstructions in the discharge and air intake 

pipes.

8. Check that the fan is working correctly.

9. Check the combustion and the correct calibration of the gas valve.

10. Check the pressure in the heating system.

11. Check the pressure in the expansion vessel.

For more information, see

Cleaning the heat exchanger, page 104

Checking the burner, page 105

Cleaning the siphon, page 106

Check the combustion, page 107

11 Maintenance

102

IX

7702703 - v04 - 05092019

Summary of Contents for IX 145-110





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands