manualshive.com logo in svg

DeDietrich IX 145-110, Installation And Service Manual

Share
Download
DeDietrich IX 145-110 Installation And Service Manual Download Page 77

Parameter 

number

Parameter

Description

Factory set­

ting

40

Used as

Operator unit 1 : The control system unit is installed on the boiler.

Room unit 1 : The control system unit is configured as a room tem­

perature unit for heating circuit 1.

Room unit 2 : The control system unit is configured as a room tem­

perature unit for heating circuit 2.

Room unit 3 : The control system unit is configured as a room tem­

perature unit for heating circuit 3.

Operator unit 

1

42

Assignment device 

1

As Room Temperature Unit 1, the action of the control system unit can 

be assigned to CC1 or to two heating circuits:

Temps / mode CH1

Central heating 1 and 2

Central Heating 1 and 3

All central heatings

All central 

heatings

43

Action operation

Locally : The room temperature unit controls only the respective 

heating circuit.

Centrally : Only room temperature unit 1 can be centralised. It also 

controls the domestic hot water and standby mode.

Centrally

54

Readjustment room 

sensor

-3°C to +3°C

0 °C

70

Software version

 

 

Tab.61 Temps / mode CH1 – Temps / mode CH2 – Temps / mode CH3 menus

Parameter number

Parameter

Description

Unit

Factory set­

ting

Heating 

circuit 1

Heating 

circuit 2

Heating 

circuit 3

714

1014

1314

Frost protection 

setpoint

°C

6

720

1020

1320

Heating curve 

slope

Heating curve gradient: The regulator calcu­

lates the flow temperature set point which is 

used for the control system, according to out­

side weather conditions.

–

Heating 

circuit 1: 

1.5

Heating 

circuit 2: 

1.5

Heating 

circuit 3: 

1.5

730

1030

1330

Summer/winter 

heating limit

Limit temperature for switching between Heat­

ing/Protection mode. Triggers or shuts down 

the heating in the course of the year according 

to variations in outside temperature. This 

switch is made automatically in Automatic 

Mode.

 

20

732

1032

1332

24-hour heating 

limit

The heating is shut down when the outside 

temperature is equal to the room tempe 

parameter 732 (deactivated in Comfort mode).

°C

0

740

1040

1340

Flow temp setpoint 

min

The flow set point calculated is limited by the 

set value.

°C

25

741

1041

1341

Flow temp setpoint 

max

The flow set point calculated is limited by the 

set value.

°C

80

742

1042

1342

Flow temp setpoint 

room stat

The set flow value is applied in room tempera­

ture thermostat mode. ‘ ---‘ the boiler is running 

in modulation mode.

°C

80

10 Settings

7702703 - v04 - 05092019

IX

77

Summary of Contents for IX 145-110





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands