manualshive.com logo in svg

DeDietrich IX 145-110, Installation And Service Manual

Share
Download
DeDietrich IX 145-110 Installation And Service Manual Download Page 9

Failure to abide by the instructions on installing and 

maintaining the appliance.

Failure to abide by the instructions on using the 

appliance.

Faulty or insufficient maintenance of the appliance.

1.3.2 

Installer's liability

The installer is responsible for the installation and initial 

commissioning of the appliance. The installer must 

observe the following instructions:

Read and follow the instructions given in the manuals 

provided with the appliance.

Install the appliance in compliance with prevailing 

legislation and standards.

Carry out initial commissioning and any checks 

necessary.

Explain the installation to the user.

If maintenance is necessary, warn the user of the 

obligation to check the appliance and keep it in good 

working order.

Give all the instruction manuals to the user.

1  Safety

7702703 - v04 - 05092019

IX

9

Summary of Contents for IX 145-110





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands