DeDietrich IX 145-110 Installation And Service Manual Download Page 58

Page: 58 / 132

2. Flush the installation with at least 3 times the volume of water

contained in the central heating system (until the water runs clear and

shows no impurities).

For more information, see

Water treatment, page 26

Flushing an existing installation

Before filling the heating installation, it is essential to remove any sludge

deposits which have accumulated in the heating circuit over the years.

1. Remove any sludge from the installation.

2. Flush the installation with at least 3 times the volume of water

contained in the central heating system (until the water runs clear and

shows no impurities).

For more information, see

Water treatment, page 26

7.8.2

Filling the siphon

1. Clean the siphon.

2. Completely fill the siphon until it overflows.

Danger

Fill the siphon to the top. If the siphon is empty, there is a danger

of poisoning by combustion products.

For more information, see

Cleaning the siphon, page 106

7.9

Completing installation

1. Reconnect the earth wire and put the front panel back in place.

2. Discard the various packaging items.

3. Affix the data plate found in the instructions bag to a visible part of the

boiler.

For more information, see

Data plate, page 31

7 Installation

7702703 - v04 - 05092019

Summary of Contents for IX 145-110





































































































































Search results

Summary of Contents for IX 145-110

Reviews:

Brands by name

Popular brands

DeDietrich IX 145-110, Installation And Service Manual

Search results

Summary of Contents for IX 145-110

Reviews:

Brands by name

Popular brands