DeDietrich IX 145-110 Installation And Service Manual Download Page 70

Page: 70 / 132

9 Operation

9.1

Use of the control panel

9.1.1

Modifying the user parameters

1. Press the

key to access the parameters.

Important
Press the

key to return to the main display.

The user parameters can now be accessed. Use the button to

select and modify them.

For more information, see

List of user parameters, page 74

9.1.2

Modifying the installer parameters

1. Press the

key to access the parameters.

2. Press the

and

keys simultaneously for at least 6 seconds.

3. Select the Commissioning menu by turning the

button.

4. Confirm the menu selection by pressing the button.

Important
Press the

key to return to the main display.

The parameters for the Commissioning mode can now be
accessed. Use the button to select and modify them.

For more information, see

List of installer parameters, page 76

9.2

Starting up the boiler

1. Open the gas cock.

Fig.70

MW-3000052-EN-02

MENU

14:13

1.5 bar

18. February 2014
Tuesday

MENU

Fig.71

MW-3000052-EN-02

MENU

14:13

1.5 bar

18. February 2014
Tuesday

MENU

Fig.72

MW-3000082-EN-03

MENU

----------------------------------------------------

Information

Set time and date

Information

9 Operation

7702703 - v04 - 05092019

Summary of Contents for IX 145-110





































































































































Search results

Summary of Contents for IX 145-110

Reviews:

Brands by name

Popular brands

DeDietrich IX 145-110, Installation And Service Manual

Search results

Summary of Contents for IX 145-110

Reviews:

Brands by name

Popular brands