manualshive.com logo in svg

Dedicated Micros SD Advanced, Installation And Operation Manual

Share
Download
Dedicated Micros SD Advanced Installation And Operation Manual Download Page 8

Dedicated Micros ©2009

SD Adv

anc

ed

Installing the Unit

Before you start

Check the contents of the box

The following items are included in the box:

Remove all items from the packaging and check the items listed below are present.

•  SD Advanced DVR (either 8, 12 or 16 input)
•  IR Remote Control (x 2)

•  Power Leads 

•  IR Extender Lead

•  SD Advanced Software/Documentation CD

•  Mouse

•  Rack Mounting brackets

•  RS485 Telemetry Adaptor

•  Quick Start Guide
If any of these items are missing please contact Dedicated Micros Technical Support team.

Note: 

Before installing the SD Advanced DVR, carefully read all Safety Instructions and the 

following information on where the unit should be located.

Choosing a location for installation

•  The SD Advanced is designed to be desk, shelf or rack mounted. Rack mounting 

brackets are available as an optional accessory.

•  Ensure the SD Advanced unit is properly ventilated to protect from overheating.
•  Ensure there is a 3cm gap on both sides of the unit.

•

 

Ensure the IR receiver on the front of the unit faces the operator position, and is not 

more than 10 feet (3 metres) from the operator. An IR Remote Control Extender is also 

available.

•  Ensure the unit is not located anywhere it could be subject to mechanical shocks.
•  The unit should be located in an area with low humidity and a minimum of dust. Avoid 

places like damp basements or loft spaces.

•  If the unit is to be installed in a closed assembly, the maximum operating temperature 

must not exceed 40°C (104°F).

•  Ensure there is reliable earthing of the mains outlet when fitted to supply connections 

(other than direct connection to the branch circuit).

•  Any branch circuit supplying the unit must be rated at 15Amps.
•  It is recommended that an uninteruptable power source be connected to the unit in 

case of power failure (to ensure continuous operation of the unit).

Summary of Contents for SD Advanced













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands