manualshive.com logo in svg

Dedicated Micros SD Advanced, Installation And Operation Manual

Share
Download
Dedicated Micros SD Advanced Installation And Operation Manual Download Page 15

Dedicated Micros ©2009

1

SD Adv

anc

ed

The SD Advanced  supports 20 normally open/closed tamper proof alarm inputs, or one Global 

keyswitch input with camera specific inputs configurable as entry/exit alarms. The alarms support 

tamper proof detection using 1k in line and 5K end of line resistance. The unit detects short circuit, 

open circuit and contact closure. This functionality is part of the advanced alarms supported on 

NetVu Connected products and includes features required for Central Monitoring. It is compatible 

with the British Standard BS8418. 

Relay Connector
Pin   

                        Alarm Input Connection

1 - 20 

1-20 

21-25 

Earth Common

End Of Line Circuitry

The following describes the EOL tamper alarms circuitry needed when EOL has been configured. 

There should be two resistive values within the tamper alarm circuitry. These must be located inside 

the alarm device (furthest point from the unit).
The alarm state could be Normally Open or Normally closed however the tamper states are the 

same for both settings.

Open, the resistive value is 6.8K ohms (1K + 5.6K).

Closed, the resistive value is 1K ohms, as the circuit does not see the 5.6K ohm resistor.

Open Circuit Tamper, the resistive value is infinity as the circuit has been cut and 

 

therefore is ‘open’.

Short Circuit Tamper, the resistive value is 0 Ohms.

Summary of Contents for SD Advanced













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands