Dedicated Micros SD Advanced Installation And Operation Manual Download Page 134

Page: 134 / 140

SD Adv

anc

Appendix D

For guidance on locating the unit’s IP address via a serial port connection, please see below:

Locating the unit IP address using the serial port

With the mains power off, connect a standard 9DF-9DF RS232 communications cable from

the PC to one of the serial port connections on the rear of the unit.

On the PC, click Start->Programs->Accessories->Communications->Hyperterminal and

create a new connection via the COM port using these settings.

Bits per second

115200

Data Bits

Parity

None

Stop bits

Flow Control

None

Power the unit, the Power LED on the unit will illuminate.

Hyperterminal will display the communications information as the unit boots up. This will

include the IP address, Subnet and Gateway.

Summary of Contents for SD Advanced













































































































































Search results

Summary of Contents for SD Advanced

Reviews:

Brands by name

Popular brands

Dedicated Micros SD Advanced, Installation And Operation Manual

Search results

Summary of Contents for SD Advanced

Reviews:

Brands by name

Popular brands