manualshive.com logo in svg

Dedicated Micros SD Advanced, Installation And Operation Manual

Share
Download
Dedicated Micros SD Advanced Installation And Operation Manual Download Page 14

Dedicated Micros ©2009

1

SD Adv

anc

ed

DHCP works by assigning an IP address at initial connection to the network. It is possible however 

that this IP address can change without notification i.e. following power failure. It is therefore 

recommended that the unit be allocated a fixed IP address. A fixed IP address can be assigned via 

the Configuration Menu pages:Network Settings->Network->IP Address.
When the unit is powered up, the network address can be found by viewing on a local monitor and 

navigating to Configuration Menu pages:System Settings->System->IP Address.
Refer to ‘Configuring The Unit’ for further guidance on locating the unit’s IP address and for details of 

the default DNS (Domain Name Server) address.
DNS (Dynamic Name Servers) is supported and therefore the unit can be assigned a name. This 

removes the need for the unit to have a fixed IP address and makes it easier for a remote user to 

locate.

Step  Relays

The SD Advanced supports up to four 24V 200mA relays. 

Relay Connector

Pins 

Connection

1 & 6 

Relay 1 signal

2 & 7 

Relay 2 signal

3 & 8 

Relay 3 signal

4 & 9 

Relay 4 signal

Step  Alarms

Summary of Contents for SD Advanced













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands