manualshive.com logo in svg

decaWave DW1000, User Manual

The decaWave DW1000 is an advanced wireless communication module that enables accurate and reliable ranging and positioning in a variety of applications. Enhance your experience with this cutting-edge technology by easily accessing the comprehensive user manual, available for free download at manualshive.com. Get the most out of your DW1000 with our detailed manual.

Share
Download
background image

DW1000 User Manual  

 

 

© Decawave Ltd 2017 

Version 2.12

 

Page 137 of 242 

 

 

Field 

Description of fields within Sub-Register 0x26:0C – GPIO_DOUT 

GOM8 

reg:26:0C 

bit:20

 

Mask for setting the GPIO8 output state.  (See GOM0). 

 

7.2.39.5 

Sub-Register 0x26:10 

– GPIO_IRQE 

ID 

Length 

(octets)

 

Type 

Mnemonic 

Description 

26:10 

4 

RW 

GPIO_IRQE 

GPIO Interrupt Enable  

 

Register file: 0x26 – GPIO control and status

, sub-register 0x10 is the GPIO interrupt enable register. The 

GPIO_IRQE register allows a GPIO input pin to be selected as an interrupt source into the DW1000.  
Additional configuration registers GPIO_IMODE, GPIO_ISEN, GPIO_IBES and GPIO_IDBE allow the interrupt 
to be set as level sensitive with control of whether it is the low or high state that generates the interrupt, or 
as edge sensitive with control of the edge(s) that generates the interrupt, and includes a configurable de-
bounce circuit that can be used to ignore transients on the input.  The GPIO_IRQE register contains a bit for 
each GPIO pin to allow each to be individually selected as interrupt source.  Setting the appropriate bit to 1 
enables the corresponding GPIO input as an interrupt source, a value of 0 disables that interrupt.  When a 
GPIO interrupt is triggered it is signalled to the host via the GPIOIRQ event status bit in 

Register file: 0x0F – 

System Event Status Register

.  The bits of the GPIO_IRQE register are as following: 

REG:26:10 – GPIO_IRQE – GPIO Interrupt Enable register 

31  30  29  28  27  26  25  24  23  22  21  20  19  18  17  16  15  14  13  12  11  10  9  8  7  6  5  4  3  2  1  0 

-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 

GIRQE8

 

GIRQE7

 

GIRQE6

 

GIRQE5

 

GIRQ E

4

 

GIRQ E

3

 

GIRQE2

 

GIRQE1

 

GIRQE0

 

0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0  0 

 
The bits identified above are individually described below: 

Field 

Description of fields within Sub-Register 0x26:10 – GPIO_IRQE 

GIRQE0 

reg:26:10 

bit:0

 

GPIO IRQ Enable for GPIO0 input.  Value 1 = enable GPIO input GPIO0 as an interrupt source.  
Value 0 = GPIO0 is not an interrupt source. 

GIRQE1 

bit:1

 

GPIO IRQ Enable for GPIO1 input.  Value 1 = enable, 0 = disable. 

GIRQE2 

bit:2

 

GPIO IRQ Enable for GPIO2 input.  Value 1 = enable, 0 = disable. 

GIRQE3 

bit:3

 

GPIO IRQ Enable for GPIO3 input.  Value 1 = enable, 0 = disable. 

GIRQE4 

bit:4

 

GPIO IRQ Enable for GPIO4 input.  Value 1 = enable, 0 = disable. 

GIRQE5 

bit:5

 

GPIO IRQ Enable for GPIO5 input.  Value 1 = enable, 0 = disable. 

GIRQE6 

bit:6

 

GPIO IRQ Enable for GPIO6 input.  Value 1 = enable, 0 = disable. 

Summary of Contents for DW1000



















































































































































































































































Reviews:

No comments

Related manuals for DW1000

B&K CT300 User Manual preview
CT300
Brand: B&K Pages: 88
B&K AVR 707 Brochure preview
AVR 707
Brand: B&K Pages: 2
Hama AT-802 Operating Instruction preview
AT-802
Brand: Hama Pages: 24
Masterplug ARCDKG Quick Manual preview
ARCDKG
Brand: Masterplug Pages: 2
Bandini Industrie GI.BI.DI. DOMINO DRC4334 Instructions For Installations preview
GI.BI.DI. DOMINO DRC4334
Brand: Bandini Industrie Pages: 2
Axxera AVM2210H Installation & Owner'S Manual preview
AVM2210H
Brand: Axxera Pages: 32
Immersion Uno 5800 User Manual preview
Uno 5800
Brand: Immersion Pages: 5
Trango Systems MTX-2500 Operating Instructions Manual preview
MTX-2500
Brand: Trango Systems Pages: 8
Teac cr-h101dab Owner'S Manual preview
cr-h101dab
Brand: Teac Pages: 200
DeviceGate Technology BT-Pusher PRO+ User Manual preview
BT-Pusher PRO+
Brand: DeviceGate Technology Pages: 17
Kramer TP-578H User Manual preview
TP-578H
Brand: Kramer Pages: 41
Dish Network DuoDVR ViP 922 User Manual preview
DuoDVR ViP 922
Brand: Dish Network Pages: 26
Optimus 31-3045 Owner'S Manual preview
31-3045
Brand: Optimus Pages: 40
Vaisala Humicap HMD60Y User Manual preview
Humicap HMD60Y
Brand: Vaisala Pages: 18
SpiderAlert MCT/IR-252 WP S User Manual preview
MCT/IR-252 WP S
Brand: SpiderAlert Pages: 2
Hallicrafters HT-44 Operation And Maintenance Manual preview
HT-44
Brand: Hallicrafters Pages: 30
Xantech Dinky Link DL95M Installation Instructions preview
Dinky Link DL95M
Brand: Xantech Pages: 4
Rover RLT-1550 D10 Operating Manual preview
RLT-1550 D10
Brand: Rover Pages: 27

Brands by name

Popular brands

Load more brands