DaVinci Category 1 Owner'S Manual Download Page 44

Page: 44 / 64

44 Installation

(for qualified installers only)

4140805

100-01384

Termination Requirements

Venting terminals shall not be recessed into a wall or siding.

Minimum 9" (229mm) clearance from any door or window

Minimum 12" (305mm) above any grade, veranda, porch, deck or balcony

Minimum 1" (25mm) from outside corner walls

NOTE

: Clearance in accordance with local installation codes and the requirements of the gas supplier.

Minimum 24" (610mm) from inside corner walls

NOTE

: Clearance in accordance with local installation codes and the requirements of the gas supplier.

Minimum 24" (610mm) clearance below ventilated or unventilated soffits or roof surfaces

NOTE

: Clearance in accordance with local installation codes and the requirements of the gas supplier.

Minimum 12" (305mm) clearance below a veranda, porch, deck or balcony

NOTE

: Permitted only if veranda, porch, deck, or balcony is fully open on a minumum of two sides beneath the floor.

NOTE

: Clearance in accordance with local installation codes and the requirements of the gas supplier.

Minimum 48" (1219mm) clearance from any adjacent building

Minimum 84" (2134mm) clearance above any grade when adjacent to public walkways or driveways
NOTE: may not be used over a walkway or driveway shared by an adjacent building

Minimum 9" (229mm) clearance to any nonmechanical air supply inlet to the building or the combustion air inlet
to any other appliance.

Minimum 36" (914mm) clearance above any mechanical air supply inlet if within 10’ (3M) horizontally

Minimum 36" (914mm) from the area above the meter/regulator (vent outlet) - this extends 15’ (4.5M) above the
regulator

NOTE

: Clearance in accordance with local installation codes and the requirements of the gas supplier.

Minimum 36" (914mm) from the meter/regulator (vent outlet)

NOTE

: Clearance in accordance with local installation codes and the requirements of the gas supplier.

M Minimum 12” (305mm) above the roof line (for vertical terminations)
N

Minimum 24” (610mm) horizontal clearance to any surface (such as an exterior wall) – for vertical terminations

•

Vent termination must not be located where it will become plugged by snow or other material

NOTE: Measure clearances to the nearest edge of the exhaust hood.

Summary of Contents for Category 1

































































Search results

Summary of Contents for Category 1

Reviews:

Related manuals for Category 1

Brands by name

Popular brands

DaVinci Category 1, Owner'S Manual

Search results

Summary of Contents for Category 1

Reviews:

Related manuals for Category 1

Brands by name

Popular brands