Dataradio Integra-TR Technical Manual Download Page 48 | Manualshive

Page: 48 / 68

Dataradio Integra-TR Technical Manual Download Page 48

2-28

Part No. 001-4008-101/102

2.4.14.1 ASCII Terminal

ASCII Terminal configurations include:

Primary

The Primary ASCII Terminal screen sends and receives ASCII data on the Primary COM Port (set up in the
Port Settings screen).

Secondary

The Secondary ASCII Terminal screen sends and receives ASCII data on the Secondary COM Port (set up
in the Port Settings screen).

2.4.14.2 HEX Terminal

Hex Terminal configurations include:

Primary

The Primary Hex Terminal screen selects a Hexadecimal Terminal screen to send and receive Hexadecimal
data on the Primary COM Port (set up in the Port Settings screen).

Secondary

The Secondary Hex Terminal screen selects a Hexadecimal Terminal screen to send and receive
Hexadecimal data on the Secondary COM Port (set up in the Port Settings screen).

2.4.15 Program Code

The Program Code pull-down menu allows the user to update the Integra-TR firmware (*.bin) with the
Program Firmware option. Select Modem Code File allows the user to select the file to program the
firmware in the Integra-TR.

2.5 INTEGRA-TR HELP FILES

Figure 2-23 Integra-TR Online Help Introductory Screen

«
...
46
47
48
49
50
...
»

Summary of Contents for Integra-TR





































































Reviews:

No comments