Archtek telecom 5634BIF User Manual Download

Page: 1 / 49

5634BIF User’s Manual

Congratulations

on purchasing the most sophisticated modem available. Your modem combines

advanced technology with state-of-the-art features to bring you the modern advanced communications
device available today!

This modem provides the following features.

Data modem

−

V.90 & K56flex

−

ITU-T V.34 (33.6 kbps), V.32 bis, V.32, V.22 bis, V.22, V.23, and V.21; Bell 212A and

103

−

V.42 LAPM, MNP 2-4, MNP 10 error correction

−

V.42 bis and MNP 5 data compression

Fax modem send and receive rate up to 14400 bps

−

ITU-T V.17, V.29, V.27 ter, V.21 channel 2

−

TIA/EIA 578 fax class 1

V.80 synchronous access mode supports host-based communication protocols

World-class operation

−

Call progress

−

Blacklisting

−

Multiple country support

Voice/TAM mode

Full-duplex speakerphone (FDSP) mode

Audio Span simultaneous audio/voice and data (SP models)

−

ITU-T V.61 modulation (4.8 kbps data plus audio)

Flash memory support

Caller ID and distinctive ring detect

Trademark

Windows and MS-DOS are trademarks of Microsoft Corporation. IBM PC/AT is a
trademark of International Business Machines. Other product or company names are
trademarks or registered trademarks of their respective holders.

Summary of Contents for 5634BIF


















































Search results

Summary of Contents for 5634BIF

Reviews:

Related manuals for 5634BIF

Brands by name

Popular brands

Archtek telecom 5634BIF, User Manual

Search results

Summary of Contents for 5634BIF

Reviews:

Related manuals for 5634BIF

Brands by name

Popular brands