manualshive.com logo in svg

Dataradio Integra-TR, Technical Manual, Page: 36 / 68

Share
Download
Dataradio Integra-TR Technical Manual Download Page 36

2-16

Part No. 001-4008-101/102

2.4.4 Apply Station Reset

Station Reset tells the Integra-TR to perform a software reset. Performing a Station Reset reacts the same as 
cycling power to the unit.

Figure 2-13   Station Reset Screen

2.4.5 Version Request

Selecting Version Request causes the Integra-TR Field Programming Software to display information about 
the version of the Integra-TR hardware and firmware.

Figure 2-14   Version Request Screen

2.4.6 Program Comment / ID

Figure 2-15   Program Comment / ID Screen

The Program Comment/ID field allows the user to program a Short ID and/or Comment. This function is 
used if the Integra-TR to be programmed was cloned from another unit (See Figure 2-15)

Short ID 

The number (1 to 254) that identifies an individual unit in a network.

Program Short ID 

Clicking this button programs the new Short ID.

Comment

This field allows the user to give each unit a unique description (s), or add customer name, location, 
technical information, or other user desired information. Comments must be text and are limited to 24 
characters, including spaces.

Summary of Contents for Integra-TR





































































Reviews:

No comments